624833

Casio 5394 - OCW-P1000 Manual

7
Zoom out
Zoom in
Previous page
1/9
Next page
Operation Guide 5394 (OC)
E-55
Adjusting Home Positions
Strong magnetism or impact can cause the hands and/or day indicator setting to be off, even if the watch
is able to perform the time calibration signal receive operation.
Auto Home Position Adjustment
Auto correction of hand home positions corrects the hand position automatically.
x Auto correction is performed in the Timekeeping Mode only.
x Auto correction corrects the positions of all hands. For the day Indicator, you must perform the manual
adjustment procedure under “To adjust home positions” (page E-56).
x If the
4
Upper Dial Hand is 12 hours off of the current correct time, correct the setting using the
procedure under “To adjust home positions” (page E-56).
Manual Home Position Adjustment
Perform the procedure in this section if auto home position adjustment is not possible for some reason.
x Hand home position adjustment is not required if the time and day settings are correct.
Note
x Any time after you enter the home position adjustment mode in step 2 of the following procedure, you
can return to the Timekeeping Mode by pushing the crown back in. In this case, any adjustments you
made before the watch returned to the Timekeeping Mode will be applied.
x If you do not perform any operation with the crown for about two minutes after pulling it out, crown
operations will become disabled. If this happens, push the crown back in and then pull it out again.
E-54
6. After the settings are the way you want, push the crown back in to exit the alarm setting mode.
x The alarm always works based on the time kept in the Timekeeping Mode.
x The watch will return to the Timekeeping Mode automatically if you do not perform any operation in
the Alarm Mode for about two or three minutes.
x If you do not perform any operation with the crown for about two minutes after pulling it out, crown
operations will become disabled. If this happens, push the crown back in and then pull it out again.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm between on and off. The
2
Second Hand will indicate the
current ON/OFF setting.
Note
x The alarm will not sound if battery power is low.
x The alarm will not sound if the watch is in the Power Saving sleep state.
To stop the alarm
Press any button.
E-53
To change the alarm time setting
1. In the Timekeeping Mode, press B four times to enter the Alarm Mode.
x The
5
Lower Dial hand will move to AL.
2. Pull out the crown to enter the alarm setting mode.
x You can toggle between the hour and minute setting mode, and the hour only setting mode by
pressing B.
Hour/Minute Hour
B
3. Rotate the crown to set the alarm time.
x The
1
Hour Hand will also move.
x See “Using the Crown” (page E-4) for information about high-speed hand movement.
4. Press B to switch to the hour setting mode.
x The
1
Hour Hand will move slightly left and right to indicate the
1
Hour Hand setting mode.
5. Rotate the crown to adjust the hour setting only.
x Check the 24-hour time indicated by the
4
Upper Dial Hand to see if the current setting is a.m. or
p.m.
x See “Using the Crown” (page E-4) for information about high-speed hand movement.
E-52
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. This is true even if the watch is not in the Timekeeping
Mode.
Hands and Indicators
1
Hour Hand: Indicates the currently set alarm time hour.
2
Second Hand: Indicates the current alarm ON/OFF setting.
3
Minute Hand: Indicates the currently set alarm time minute.
4
Upper Dial Hand: Indicates the hour setting of the current alarm time in
24-hour format.
5
Lower Dial Hand: Points to AL.

E-51
3. Rotate the crown to set the countdown start time.
x The maximum countdown start time setting is 60 minutes. To set a countdown start time of 60 minutes,
move the
3
Minute Hand to 12 o’clock.
x See “Using the Crown” (page E-4) for information about high-speed hand movement.
4. Push the crown back in to exit the countdown start time setting mode.
x If you do not perform any operation with the crown for about two minutes after pulling it out, crown
operations will become disabled. If this happens, push the crown back in and then pull it out again.
To perform a countdown timer operation
A
A C
Start Stop Zero Reset
x A time-up alert sounds for 10 seconds when the countdown reaches 0, and then the timer displays the
start time.
x The alarm will not sound if battery power is low.
x Pulling out the crown while a countdown is in progress will stop the countdown and enter the
countdown start time setting mode.
Important!
x Time calibration signal reception is disabled while the watch is in the Countdown Timer Mode.
To stop the alarm
Press any button.
E-50
Using the Countdown Timer
The countdown timer start time can be set in one-minute increments up to 60 minutes. An alarm sounds
for about 10 seconds when the timer reaches zero.
Hands and Indicators
2
Second Hand: Indicates countdown or elapsed seconds.
3
Minute Hand: Indicates countdown or elapsed minutes.
5
Lower Dial Hand: Points to TR.
x All hands move counterclockwise during a countdown.
To specify the countdown start time
1. In the Timekeeping Mode, press B three times to enter the Countdown
Timer Mode.
x The
5
Lower Dial Hand will move to TR.
2. In the Countdown Timer Mode, pull out the crown.
x This enters the countdown start time setting mode.


E-49
To enter and exit the Stopwatch Mode
In the Timekeeping Mode, press B twice to enter the Stopwatch Mode.
x The
5
Lower Dial Hand will move to ST.
To perform an elapsed time operation
A
A A A C
Start Stop (Restart) (Stop) Zero Reset
To perform fl yback timing
Pressing C while an elapsed time operation is in progress performs zero reset and immediately resumes
timing from there. You can do this as many times as you want.
A C C
.....
A C
Start 1 Start 2 Start 3 Stop Zero Reset
x An ongoing elapsed time measurement operation continues even if you pull out the crown or changing
to a different mode.
x The
2
Second Hand, which indicates the 1/20 (0.05)-second count during stopwatch operation, moves
only 30 seconds after an elapsed time measurement operation is started or restarted. After that, the
2
Second Hand stops.
E-48
Using the Stopwatch
You can use the stopwatch to measure elapsed times. A fl yback feature (page E-49) lets you reset the
stopwatch to zero without stopping time measurement.
Hands and Indicators
1
Hour Hand: Indicates the stopwatch minute count
(1 revolution = 60 minutes).
2
Second Hand: Indicates the 1/20 (0.05)-second count during stopwatch
operation.
3
Minute Hand: Indicates the stopwatch seconds count.
4
Upper Dial Hand: Indicates the stopwatch minute count
(1 revolution = 120 minutes).
5
Lower Dial Hand: Points to ST.

7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5394 - OCW-P1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5394 - OCW-P1000 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info