624960
4
Zoom out
Zoom in
Previous page
1/5
Next page
Operation Guide 5283/5332
E-38
Illumination
The face of the watch is illuminated for easy reading in
the dark.
To turn on illumination
In any mode (except when a setting mode, with fl ashing
digits is on the display), press B to illuminate the display.
You can use the procedure below to select either
1.5 seconds or 3 seconds as the illumination duration.
When you press B, the display will remain illuminated
for about 1.5 seconds or 3 seconds, depending on the
current illumination duration setting.
E-37
If you need to advance the analog time setting a long way, hold down D until
the time starts advancing at high speed, and then press B. This locks the high-
speed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (daily alarm, Hourly Time Signal,
or countdown beeper) starts to sound.
Press 4. A to exit the setting mode.
The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting mode.
To return to the Timekeeping Mode, press C.
E-36
Adjusting the Analog Hand Setting
Use the following procedure to adjust the analog hands so their settings match the
digital time.
To adjust the analog time
Use 1. C to select the Hand Setting Mode as shown on
page E-11.
Hold down 2. A until the current digital time starts to
ash, which indicates the analog setting mode.
Press 3. D to advance the analog time setting by
20 seconds.
Holding down D advances the analog time setting
at high speed.
E-35
Press 5. A to exit the setting mode.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
In the Alarm Mode, use 1. D to select an alarm or the
Hourly Time Signal.
When the alarm or the Hourly Time Signal you want is 2.
selected, press A to toggle it between on and off.
The alarm on indicator (when any alarm is on), snooze
alarm indicator (when the snooze alarm is on), and the
Hourly Time Signal on indicator (when the Hourly Time
Signal is on) are shown on the display in all modes.
To stop the alarm
Press any button.
Hourly time signal
on indicator
Snooze alarm indicator
E-34
To set an alarm time
In the Alarm Mode, use 1. D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
AL1 AL3 SNZAL2 AL4 SIG
D D DD D
D
Hold down 2. A for about two seconds until the alarm time starts to fl ash. This is
the setting mode.
Press 3. C to move the fl ashing between the hour and minute settings.
While a setting is fl ashing, use 4. D (+) and B (–) to change it.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
Alarm ON/OFF indicator
E-33
To enter the Alarm Mode
Use C to select the Alarm Mode as shown on page E-11.
The snooze alarm screen is indicated by SNZ, while the other alarm screens are
numbered AL1 through AL4. The Hourly Time Signal screen is indicated by SIG.
When you enter the Alarm Mode, the data you were viewing when you last exited
the mode appears rst.
E-32
Using the Alarm
You can set fi ve independent daily alarms. When a
daily alarm is turned on, an alarm tone will sound
for about 20 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. One
of the alarms is a snooze alarm, while the other four
are one-time alarms. The snooze alarm operation will
repeat every ve minutes, up to seven times.
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
Alarm number
Alarm time (Hour : Minutes)
E-31
Note
The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59 seconds.
Once started, stopwatch timing continues until you press D to stop it, even if
you exit the Stopwatch Mode to another mode and even if timing reaches the
stopwatch limit defi ned above.
Exiting the Stopwatch Mode while a split time is frozen on the display clears the
split time and returns to elapsed time measurement.
E-30
To perform an elapsed time operation
D
D D D A
Start Stop (Restart) (Stop) Reset
To pause at a split time
D
A A D A
Start Split
(SPL displayed)
Split release Stop Reset
To measure two fi nishes
D
A D A A
Start Split
(SPL displayed)
First runner nishes.
Display time of rst
runner.
Stop
Second runner
nishes.
Split release
Display time of
second runner.
Reset
E-39
in
hing
splay.
on.
ted
the
To change the illumination duration
In the Timekeeping Mode, hold down 1. A until the seconds start to fl ash. This is
the setting mode.
Press 2. C nine times so the illumination duration setting mode is on the display.
Press 3. D to toggle the illumination duration between 1.5 seconds (
) and
3 seconds (
).
After the settings are the way you want, press 4. A to exit the setting mode.
Illumination Precautions
Illumination may be hard to see when viewed under direct sunlight.
Illumination turns off automatically whenever an alarm sounds.
Frequent use of illumination runs down the battery.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 5283 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 5283 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 5283

Casio 5283 User Manual - German - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info