586707
3
Zoom out
Zoom in
Previous page
1/5
Next page
Operation Guide 4709 4713
3
To turn auto receive on and off
1. Press B to display the Last Signal screen.
2. Hold down A so the current auto receive setting (R/C
on or R/C OF) is flashing. This is the setting screen.
Though illumination will also turn on when you press
A, keep the button held down until R/C on or R/C OF
flashes.
Note that the setting screen will not appear if the
currently selected Home Time Zone is one that does
not support time calibration reception.
3. Press C to toggle auto receive on (on) and off (OF).
4. Press A to exit the setting screen.
For information about time zones that support signal
receive, see “To specify your Home Time Zone”.
On/Off status
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
To check the latest signal reception results
Press B to display the Last Signal screen.
The display shows the time and date that receive was
successful. - - : - - indicates that none of the reception
operations were successful.
To return to the Timekeeping Mode, press B.
Receive date
Receive time
Problem
Cannot perform
manual receive.
Time setting is
incorrect
following signal
reception.
Probable Cause
The watch is not in the Timekeeping
Mode.
Your current Home Time Zone is not one
of the following:
UTC +0, UTC +1, UTC +2, UTC +8, UTC
+9, UTC 10, UTC 9, UTC 8, UTC 7,
UTC 6, or UTC 5
( DST ON : UTC +1, UTC +2, UTC +3,
UTC +9, UTC +10, UTC 9, UTC 8,
UTC 7, UTC 6, UTC 5, or UTC 4 )
If the time is one hour off, the DST
setting may be incorrect.
The Home Time Zone setting is not correct
for the area where you are using the watch
.
What you should do
Enter the Timekeeping Mode
and try again
.
Select UTC +0, UTC +1, UTC
+2, UTC +8, UTC +9, UTC
10, UTC 9, UTC 8, UTC
7, UTC 6, or UTC 5
( DST ON : UTC +1, UTC +2,
UTC +3, UTC +9, UTC +10,
UTC 9, UTC 8, UTC 7,
UTC 6, UTC 5, or UTC 4 )
as your Home Time Zone
.
Change the DST setting to
Auto DST
.
Select the correct Home Time
Zone
.
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Atomic Timekeeping Precautions”.
Dual Time
The Dual Time Mode shows you the current time in 29
time zones around the world.
If the current time shown for a time zone is wrong, check
your Home Time Zone time settings and make the
necessary changes.
All of the operations in this section are performed in the
Dual Time Mode, which you enter by pressing B.
To view the time in another Time Zone
1. In the Dual Time Mode, press C to display the UTC differential value of the
currently selected time zone for about two seconds.
2. To change the UTC differential value, press C while a UTC differential value is on
the display to scroll eastward through time zones.
Note that if you do not press C to scroll within two seconds after displaying a
UTC differential value, the display will change automatically to the current time
based on the currently displayed UTC differential value.
3. When the UTC differential value you want is on the display, do not perform any
button operation for about two seconds. This will cause the current time to appear,
which will be based on the UTC differential value you selected.
Current time
in selected
time zone
To toggle a time zone time between Standard Time and Daylight Saving Time
1. In the Dual Time Mode, use C to display the time zone
whose Standard Time/Daylight Saving Time setting you
want to change.
2. Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
Turning on DST causes the UTC differential value to be increased by one.
Though illumination will also turn on when you press A, keep the button held down
until DST indicator displayed or DST indicator not displayed.
The DST indicator will appear whenever you display a time zone for which Daylight
Saving Time is turned on.
Note that the DST/Standard Time setting affects only the currently displayed time
zone. Other time zones are not affected.
Note that you cannot switch between Standard Time and Daylight Saving Time while
UTC is selected as the time zone.
Note that you cannot use the Dual Time Mode to change the DST setting of the
Home Time Zone you currently have selected in the Timekeeping Mode. See “To
change the Daylight Saving Time (summer time) setting” for information about
turning the Home Time Zone DST setting on and off.
DST indicator
Alarm
You can set a Daily Alarm. When an alarm is turned on, the alarm tone sounds when
the alarm time is reached.
You can also turn on an Hourly Time Signal that causes the watch to beep twice every
hour on the hour.
When you enter the Alarm Mode, the screen you were viewing when you last exited
the mode appears first.
All of the operations in this section are performed in the Alarm Mode, which you
enter by pressing B.
In the Alarm Mode, you can press C to toggle the display contents as shown below.
Alarm screen
Hourly Time Signal screen
Hourly time signal on/off status
Alarm time
(Hour: Minutes)
Timekeeping
Mode Seconds
To set an alarm time, and to turn Alarm on and off
1. In the Alarm Mode, use C to display the Alarm Screen.
2. Hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
Though illumination will also turn on when you press
A, keep the button held down until the hour setting of
the alarm time flashes.
This operation automatically turns on the alarm.
3. Press B to change the flashing contents in the sequence shown below to select
other settings.
Hour Minutes Alarm On/Off
I
I
I
I
I
I
I
I
I
I
I
I
I
4.
When the setting you want to change is flashing, use
C
to change it as described below.
Screen: To do this:
Change the hour or minutes
Toggle between alarm on (
),
and alarm off (
)
Do this:
Use C.
Press C.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds.
Note
Pressing any button stops the alarm tone operation.
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
To turn the hourly time signal on and off
1. In the Alarm Mode, use C to display the Hourly Time
Signal Screen.
2. Hold down A until the hourly time signal on/off status
starts to flash, which indicates the setting screen.
Though illumination will also turn on when you press
A, keep the button held down until the hourly time
signal on/off status flashes.
This operation automatically turns on the hourly time
signal.
3. Press C to toggle it on and off.
4. Press A to exit the setting screen.
On/off status
Stopwatch
The stopwatch lets you measure elapsed time.
The display range of the stopwatch is 59 minutes, 59.99
seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
Minutes
Seconds
Elapsed Time Measurement
Elapsed Time Screen
Seconds
1/100 seconds
Timekeeping
Mode Seconds
Minutes
Seconds
Timekeeping
Mode Seconds
Minutes
Seconds
Timekeeping
Mode Seconds
1/100 seconds
Up to one minute
From one minute
C
Start Stop
C
Re-start Clear
Stop
C
C
Hold downC
To measure times with the stopwatch
Elapsed Time
Illumination
An LED (light-emitting diodes) illuminate the digital display
for easy reading in the dark.
See “Illumination Precautions” for other important
information.
To turn on illumination
In any mode (except when a setting screen is on the
display), press A to illuminate the digital display.
When turning on illumination, press A and immediately release it. If you keep A
held down too long, either of the operations described below will be peformed.
If you hold down A while in the Timekeeping Mode, Alarm Mode, or Hand
Setting Mode
The figures on the display will start to flash, which indicates the setting screen. If
this happens, press A again to exit the setting screen.
If you hold down A while in the Dual Time Mode
The DST setting will toggle between Standard Time and Daylight Saving Time,
which will affect the current time setting.
If this happens, hold down A again to toggle setting back to its original setting (if
necessary).
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 4713 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 4713 in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 4713

Casio 4713 User Manual - German - 6 pages

Casio 4713 User Manual - Dutch - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info