624855
8
Zoom out
Zoom in
Previous page
1/10
Next page
8
Operation Guide 3173 3246
To confi gure longitude and latitude settings
1. In the Timekeeping Mode, hold down
E
until the currently selected
city code starts to fl ash. This is the city code setting screen.
Before the city code starts to fl ash, the message SET Hold
will appear on the display. Keep
E
depressed until SET Hold
disappears and the city code starts to fl ash.
2. Press
E
to display the longitude/latitude setting screen, with the
latitude setting fl ashing.
3. Use
D
to move the fl ashing between the latitude and the longitude
setting.
4. Use
A
(+) and
C
(–) to change the fl ashing setting.
You can configure the longitude and latitude setting within
following ranges.
Latitude Range: 65°S (South 65 degrees) to 0°N – 65°N (North 65
degrees)
Longitude Range: 179°W (West 179 degrees) to 0°E – 180°E (East
180 degrees)
Latitude and longitude values are rounded off to the nearest
degree.
You can fi nd latitude and longitude for various cities around the
globe in the “Site Data List”.
5. Press
E
to return to the Timekeeping Mode.
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 31 time zones (48 cities) around the
globe. The city that is currently selected in the World Time Mode is called the “World Time City”.
To enter the World Time Mode
Use
D
to select the World Time Mode (
WT
) as shown in “Selecting a
Mode”.
About one second after
WT
appears on the display, the display will
change to show the city code of the currently selected World Time City.
The two pointers described below are on the display in the World Time
Mode.
Pointer 1 (not fl ashing): Indicates the current time in the currently
selected World Time City in 24-hour format.
Pointer 2 (fl ashing): Indicates the current Timekeeping Mode time in
24-hour format.
To view the time in another time zone
In the World Time Mode, use
A
(East) and
C
(West) to scroll through city codes.
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use
A
(East) and
C
(West) to display the
city code (time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
E
until
DST Hold
appears on the display and then
disappears. Release
E
after
DST Hold
disappears.
This toggles the city code you selected in step 1 between Daylight
Saving Time (DST indicator displayed) and standard time (DST
indicator not displayed).
Using the World Time Mode to change the DST setting of the
city code that is selected as your Home City also will change the
Timekeeping Mode time DST setting.
Note that you cannot switch between standard time/daylight
saving time (DST) while UTC is selected as the World Time City.
Note that the standard time/daylight saving time (DST) setting
affects only the currently selected time zone. Other time zones are
not affected.
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use
D
to select the Stopwatch Mode (
STW
) as shown in “Selecting a
Mode”.
About one second after
STW
appears on the display, the display will
change to show the stopwatch hours.
To perform an elapsed time operation
A
A
A A
C
Start Stop (Restart) (Stop) Reset
To pause at a split time
A
C
C A
C
Start Split
(
SPL
displayed)
Split release Stop Reset
To measure two fi nishes
A
C
A C
C
Start Split
First runner fi nishes.
Display time of fi rst
runner
Stop
Second runner
nishes.
Split release
Display time of
second runner
Reset
Note
The Stopwatch Mode can indicate elapsed time up to 23 hours, 59 minutes, 59.99 seconds.
Once started, stopwatch timing continues until you press
C
to stop it, even if you exit the Stopwatch
Mode to another mode and even if timing reaches the stopwatch limit defi ned above.
Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns
to elapsed time measurement.
Latitude
Longitude
Press D.
Latitude
Longitude
Press D.
Pointer 1
Currently selected
World Time City
Current time in the
currently selected
World Time City
Pointer 2
Current
Timekeeping
Mode time
Pointer 1
Currently selected
World Time City
Current time in the
currently selected
World Time City
Pointer 2
Current
Timekeeping
Mode time
DST indicatorDST indicator
Hours
1/100 second
Seconds
Minutes
Current
time
Hours
1/100 second
Seconds
Minutes
Current
time
Using the Countdown Timer
The countdown timer can be confi gured to start at a preset time, and sound an alarm when the end of the
countdown is reached.
To enter the Countdown Timer Mode
Use
D
to select the Countdown Timer Mode (
TMR
) as shown in “Selecting a
Mode”.
About one second after
TMR
appears on the display, the display will
change to show the countdown time hours.
To specify the countdown start time
1. Enter the Countdown Timer Mode.
If a countdown is in progress (indicated by the seconds counting
down), press
A
to stop it and then press
C
to reset to the current
countdown start time.
If a countdown is paused, press
C
to reset to the current
countdown start time.
2. Hold down
E
until the hour setting of the current countdown start time
starts to fl ash. This is the setting screen.
Before the hour setting starts to fl ash, the message SET Hold
will appear on the display. Keep
E
depressed until SET Hold
disappears and the hour setting starts to fl ash.
3. Press
D
to move the fl ashing between the hour and minute settings.
4. Use
A
(+) and
C
(–) to change the fl ashing item.
To set the starting value of the countdown time to 24 hours, set 0H 00’00.
5. Press
E
to exit the setting screen.
To perform a countdown timer operation
A
A
A A
C
Start Stop (Restart) (Stop) Reset
Before starting a countdown timer operation, check to make sure that a countdown operation is not in
progress (indicated by the seconds counting down). If it is, press
A
to stop it and then
C
to reset to
the countdown start time.
An alarm sounds for fi ve seconds when the end of the countdown is reached. This alarm will sound in
all modes. The countdown time is reset to its starting value automatically when the alarm sounds.
To stop the alarm
Press any button.
Using the Alarm
You can set fi ve independent daily alarms. When an alarm is turned on,
an alarm will sound for about 10 seconds each day when the time in the
Timekeeping Mode reaches the preset alarm time. This is true even if the
watch is not in the Timekeeping Mode.
You can also turn on an Hourly Time Signal, which will cause the watch
to beep twice every hour on the hour.
To enter the Alarm Mode
Use
D
to select the Alarm Mode (
ALM
) as shown in “Selecting a Mode”.
About one second after
ALM
appears on the display, the display will
change to show an alarm number (
AL1
through
AL5
) or the
SIG
indicator. The alarm number indicates an alarm screen.
SIG
is shown
when the Hourly Time Signal screen is on the display.
When you enter the Alarm Mode, the data you were viewing when you
last exited the mode appears fi rst.
To set an alarm time
1. In the Alarm Mode, use
A
and
C
to scroll through the alarm screens
until the one whose time you want to set is displayed.
AL1 AL2 AL3
SIG AL5
AL4
2. Hold down
E
until the alarm time starts to fl ash. This is the setting
screen.
Before the alarm time starts to fl ash, the message SET Hold
will appear on the display. Keep
E
depressed until SET Hold
disappears and the alarm time starts to fl ash.
3. Press
D
to move the fl ashing between the hour and minute settings.
4. While a setting is fl ashing, use
A
(+) and
C
(–) to change it.
When setting the alarm time using the 12-hour format, take care to set the time correctly as a.m. (no
indicator) or p.m. (P indicator).
5. Press
E
to exit the setting screen.
To test the alarm
In the Alarm Mode, hold down
A
to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use
A
and
C
to select an alarm or the Hourly
Time Signal.
2. When the alarm or the Hourly Time Signal you want is selected, press
B
to turn it on and off.
The alarm on indicator and the Hourly Time Signal on indicator are
shown on the display in all modes while these functions are turned on.
If any alarm is on, the alarm on indicator is shown on the display in
all modes.
To stop the alarm
Press any button.
Current time
Countdown time
(Hour, minutes,
seconds)
Current time
Countdown time
(Hour, minutes,
seconds)
Alarm
number or
SIG
Alarm time
(Hour : Minutes)
Current time
Alarm
number or
SIG
Alarm time
(Hour : Minutes)
Current time
Alarm ON/OFF
indicator
Alarm ON/OFF
indicator
Module 3173
Module 3246
Hourly time signal
on indicator
Alarm on indicator
Module 3173
Module 3246
Hourly time signal
on indicator
Alarm on indicator
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 3246 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3246 in the language / languages: English as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 3246

Casio 3246 User Manual - German - 11 pages

Casio 3246 User Manual - Dutch - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info