466628
10
Zoom out
Zoom in
Previous page
1/12
Next page
Operation Guide 3147
10
To set the time and date manually
1. In the Timekeeping Mode, hold down A until the city code starts to flash,
which indicates the setting screen.
2. Use E and B to select the city code you want.
Make sure you select your Home City code before changing any other
setting.
For full information on city codes, see the City Code Table.
3. Press D to move the flashing in the sequence shown below to select the
other settings.
Year
Seconds
Hour
Minutes
Day
Month
12/24-Hour
Format
Power
Saving
Barometric
Pressure Unit
Altitude Unit
Temperature
Unit
City Code
DST
The following steps explain how to configure timekeeping settings only.
4. When the timekeeping setting you want to change is flashing, use E and/
or B to change it as described below.
Do this:
Use E (east) and
B(west).
Press E.
Press E.
To do this:
Change the city code
Cycle between Auto DST (AvtA),
Daylight Saving Time (
ON) and
Standard Time (OFF).
Toggle between 12-hour (
12H
)
and 24-hour (
24H
) timekeeping.
Screen
ON
5. Press A to exit the setting screen.
Note
Auto DST (
AvtA) can be selected only while
LON
,
PAR
,
BER
,
ATH
,
HKG
,
TPE
,
TYO
,
LAX
,
DEN
,
CHI
, or
NYC
is selected as the
Home City code. For more information, see Daylight Saving Time (DST)
below.
You also need to enter the Timekeeping Mode in order to configure the
following settings.
Power saving on/off (To turn Power Saving on and off)
Temperature, barometric pressure, and altitude units (To select the
temperature, barometric pressure, and altitude units)
Press E.
Use E (+) and B ().
Reset the seconds to
00
Change the hour or minutes
Change the year, month, or day
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour
from Standard Time. Remember that not all countries or even local areas use
Daylight Saving Time.
The time calibration signals transmitted from Mainflingen (Germany), Anthorn
(England), or Fort Collins (the United States) include both Standard Time and
DST data. When the Auto DST setting is turned on, the watch switches
between Standard Time and DST (summer time) automatically in accordance
with the signals.
Though the time calibration signal transmitted by the Fukushima and
Fukuoka/Saga, Japan transmitters include summer time data, summer time
currently is not implemented in Japan (as of 2007).
The default DST setting is Auto DST (
AvtA) whenever you select
LON
,
PAR
,
BER
,
ATH
,
HKG
,
TPE
,
TYO
,
LAX
,
DEN
,
CHI
, or
NYC
as your Home City code.
If you experience problems receiving the time calibration signal in your
area, it probably is best to switch between Standard Time and Daylight
Saving Time (summer time) manually.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until
the city code starts to flash, which indicates
the setting screen.
2. Press D and the DST setting screen appears.
3. Use E to cycle through the DST settings in
the sequence shown below.
Auto DST (
AvtA
) DST off (
OFF
) DST on (
ON
)
If you change your Home City to one that is within the same transmitter
area, the current DST setting will be retained. If you change to a city that is
outside your current transmitter area, DST will be turned off automatically.
Transmitter area city codes
HKG, TPE, and TYO
LAX, DEN, CHI, NYC, ANC, and HNL
LON, PAR, BER, and ATH
All other city codes
4. When the setting you want is selected, press A to exit the setting screen.
The DST indicator appears to indicate that Daylight Saving Time is turned on.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
DST indicator
Reference
This section contains more detailed and technical information about watch
operation. It also contains important precautions and notes about the various
features and functions of this watch.
Auto Return Features
The watch returns to the Timekeeping Mode automatically if you do not
perform any button operation for two or three minutes in the Data Recall,
Alarm, Receive, or Barometer/Thermometer Mode.
If you do not perform any button operation for 21 or 22 hours while in the
Altimeter Mode, the watch will return to the Timekeeping Mode
automatically.
If you leave a screen with flashing digits on the display for two or three
minutes without performing any operation, the watch exits the setting
screen automatically.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
Scrolling
The E and B buttons are used on the setting screen to scroll through data
on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Sensor Malfunction Indicator
Subjecting the watch to strong impact can cause sensor malfunction or
improper contact of internal circuitry. When this happens,
ERR
(error) will
appear on the display and sensor operations will be disabled.
Barometric Pressure
Measurement
Altitude
Measurement
If ERR appears while a measurement operation is being performed in a
sensor mode, restart the measurement. If
ERR appears on the display
again, it can mean there is something wrong with the sensor.
Even if battery power is at Level 1 or Level 2, the Barometer/Thermometer
Mode or Altimeter Mode sensor may be disabled if there is not enough
voltage available to power it sufficiently. In this case,
ERR will appear on
the display. This does not indicate malfunction, and sensor operation should
resume once battery voltage returns to its normal level.
If
ERR keeps appearing during measurement, it could mean there is a
problem with the applicable sensor.
Whenever you have a sensor malfunction, be sure to take the watch to
your original dealer or nearest authorized CASIO distributor as soon as
possible.
Button Operation Tone
The button operation tone sounds any time you
press one of the watchs buttons. You can turn the
button operation tone on or off as desired.
Even if you turn off the button operation tone,
the alarm, Hourly Time Signal, and Countdown
Timer Mode alarm all operate normally.
To turn the button operation tone on and off
In any mode (except when a setting screen is on
the display), hold down D to toggle the button
operation tone on (MUTE not displayed) and off
(MUTE displayed).
Since the D button is also the mode change button, holding it down to turn
the button operation on or off also causes the watchs current mode to
change.
The MUTE indicator is displayed in all modes when the button operation
tone is turned off.
Mute indicator
Power Saving
When turned on, Power Saving enters a sleep
state automatically whenever the watch is left for
a certain period in an area where it is dark. The
table below shows how watch functions are
affected by Power Saving.
There actually are two sleep state levels:
display sleep and function sleep.
Elapsed Time in
Dark
60 to 70 minutes
(Display Sleep)
6 or 7 days
(Function Sleep)
Display
Blank, with
PS flashing
Blank, with
PS not flashing
Operation
Display is off, but all functions
are enabled.
All functions are disabled, but
timekeeping is maintained.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 3147 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 3147 in the language / languages: English as an attachment in your email.

The manual is 5,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 3147

Casio 3147 User Manual - German - 13 pages

Casio 3147 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info