55687
2
Zoom out
Zoom in
Previous page
1/4
Next page
Operation Guide 2548/2821
2
To recall e-DATA MEMORY records
In the e-DATA MEMORY Mode, use D (+) and B () to cycle through e-DATA
MEMORY records as shown below.
Press .
Press .
Remaining
memory
screen
Record 1
() Record 2
()
Password
setting
screen
Remaining Memory Screen Password Setting Screen
The value on the remaining memory screen is the percentage of memory that
is still available. It does not indicate the number of records that can be stored.
The Password Setting screen shows xxxx when a password is already
registered.
You can use the Password Setting screen to register, edit, or delete your
password. See Using a Password to Protect e-DATA MEMORY Data for
more information.
To edit an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B () to display the record
you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D (+) and B () to change the character.
5. After making the changes you want, press A to store them and return to the
e-DATA MEMORY record screen.
To delete an e-DATA MEMORY record
1. In the e-DATA MEMORY Mode, use D (+) and B () to display the record
you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Press B and D at the same time to delete the record.
The message CLR appears to indicate that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for
input.
4. Input data or press A to return to the remaining memory screen.
Using a Password to Protect e-DATA MEMORY Data
You can register a 4-digit password to keep e-DATA MEMORY data secure.
Important!
Use a 4-digit password that is easy for you to remember, but difficult for others
to decipher. If you forget the password, you will have to have your watch
initialized (which deletes all data in memory) in order to access the e-DATA
MEMORY again. To have the watch initialized, contact the store or dealer where
you purchased it, and ask to have the AC operation performed.
To register a new password
1. In the e-DATA MEMORY Mode, use D (+) and
B () to display the Password Setting screen.
This displays a screen that shows SET PA55.
2. Hold down A for about one second until NEW
appears, with the first 0 flashing.
This is the New Password Setting screen.
3. Use D (+) and B () to scroll through numbers at the first digit.
4. When the first digit is the number you want, press C to advance to the next digit.
5. Repeat steps 3 and 4 to input all four digits of the password you want.
Pressing A while inputting a new password clears your input and returns to the
Password Setting screen.
6. After all four of the password digits are the way you want, press C to register
them.
Pressing C causes the message SET to appear for about one second as the
password is stored. After that, the Password Setting screen appears.
After registering a password, you can input, recall, edit and delete data, if you want.
After you exit the e-DATA MEMORY Mode, you will have to input the password
every time you want to enter it again.
To input the password
1. Enter the e-DATA MEMORY Mode.
2. On the Password Input screen (xxxx PA55), press D
or B. This causes the first digit of the password to
flash.
3. Input the password.
Use D (+) and B () to scroll through numbers at
each digit.
Press C to advance to the next digit.
Pressing A while inputting the password clears your
input and returns to the Password Input screen.
4. After the password is the way you want, press C.
If the input password matches the one registered, the message OK!appears,
followed by an e-DATA MEMORY screen.
If the password does not match, the message ERR appears, followed by the
Password Input screen.
To change the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B () to display the Password Setting screen.
3. Perform the procedure starting from step 2 under To register a new password to
specify the new password.
To delete the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B () to display the Password Setting screen.
3. Hold down A for about one second until NEW appears, with the first 0 flashing.
4. Press B and D at the same time to delete the password.
The message CLR appears to indicate that the password is being deleted. After the
password is deleted, the Password Setting screen appears.
World Time
World Time shows the current time in 27 cities (29 time
zones) around the world.
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city code
In the World Time Mode, press D to scroll through city
codes (time zones) to the east or B to scroll to the west.
For full information about city codes, see the City Code
Table.
If the current time shown for a city is wrong, check your
Timekeeping Mode time and Home City code settings
and make the necessary changes.
When the currently selected time zone is one that includes
mostly ocean, a value indicating the zones Greenwich
Mean Time differential appears in place of a city code.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use B and D to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about one second to toggle Daylight
Saving Time (DST displayed) and Standard Time (DST
not displayed).
The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT is selected as the city code.
Current time in the zone
of the selected city code
Timekeeping
Mode time
City code
Alarms
You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms is a snooze alarm, while the
other four are one-time alarms. You can also input
reminder text that appears when the alarm time is
reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
There are five alarm screens numbered AL1through
AL4 for the one-time alarm, a snooze alarm screen
indicated by SNZ. The Hourly Time Signal screen is
indicated by SIG.
In the case of the snooze alarm screen, the snooze
alarm indicator ( ) appears in the lower right corner
of the display.
Alarm settings (and Hourly Time Signal settings) are available in the Alarm Mode,
which you enter by pressing C.
Alarm Types
The alarm type is determined by the settings you make, as described below.
Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
To set an alarm time
1. In the Alarm Mode, use D and B to scroll through the
alarm screens until the one whose time you want to set
is displayed.
Press .
Press .
To set a one-time alarm, display one of the screens indicated by an alarm number
from AL1through AL4. To set the snooze alarm, display the screen indicated
by SNZ.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
This operation automatically turns on the alarm.
3. Press C to move the flashing in the sequence shown below to select other settings.
Hour TextMinutes Month Day
Selecting the text causes the text input cursor (#) to appear. There are eight
spaces in the text, so you have to press C eight times to move to the Hour
setting.
Alarm time
(Hour : Minutes)
Alarm number
Timekeeping Mode time
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Casio 2548 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Casio 2548 in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Casio 2548

Casio 2548 User Manual - German - 5 pages

Casio 2548 User Manual - Dutch - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info