469918

Carrera Digital 124 - 30352 Control Unit Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
9
Connections
Control elements


Encoding/programming
of cars to the according
speed controllers




To encode a car place it on the track and swich on the Control
Unit.
Press “Code” button once
, g.
; the rst LED starts to light,
g.
. Then push lane-change-button once on the relevant speed
controller, g.
. In case the car is equipped with lights they will
start to ash and the Control Unit´s LEDs 2-4 will light successively.
Once encoding has been carried out the middle LED lights perma-
nently (g.
) and the car is allocated to the speed controller.
 This kind of encoding requires to have  on the
racetrack .
Encoding/programming
of Autonomous Car




300
150
250
200
0
100
50
SPEED
+
CLICK
Switch on the Control Unit, place the car to be encoded on the track
and press „Code“
twice, g.
. The rst two LEDs at the Con-
trol Unit start to light, g.
. Now push the lane-change button at
the speed controller, g.
; LEDs 3-5 will light successively. Wait
until the middle LED lights again, g.
. Activate the speed
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, g.
.
Autonomous Car´s encoding is completed now.
 This kind of encoding requires having   on the
track   . The programming of the Autono-
mous Car will be maintained unless the car is not being recoded.
The Autonomous Car is always displayed with address 7 in combi-
nation with the Position Tower.
Encoding/programming
Pace Car
Pit Lane 30356




300
150
250
200
0
100
50
SPEED
+
CLICK
(only in combination with Pit Stop Lane #30356)
Switch on the Control Unit, place the car to be encoded on the track
and press “Code″
three times, g.
. The rst three LEDs at
the Control Unit start to light, g.
. Now push the lane-change but-
ton at the speed controller, g.
; LEDs 2-5 will light successively.
Wait until the middle LED lights again, g.
. Activate the speed
controller´s tappet until the car has reached the desired speed. Now
push lane-change button again, g.
. The Pace Car´s encoding is
completed now and the car enters the Pit Stop Lane.
This kind of encoding requires having   on the
track . The programming of the Pace Car
will be maintained unless the car is not being recoded. The Pace
Car is always displayed with address 8 in combination with the Posi-
tion Tower.

After the Pace Car´s encoding has been completed it will auto-
matically enter the Pit Lane during the rst laps. In order to start the
Pace Car please push the button “Pace Car”
once. The LEDs
2 and 3 at the Control Unit will light and the Pace Car will leave the
Pit Lane. The Pace Car will now drive as long as the button „Pace
Car“ is pushed again. LED 2 stops lighting and the car automatically
enters the Pit Lane within the current lap.
Display of position
Autonomous and Pace Car


Position
Tower
30357





(only in combination with Position Tower #30357)
The position of the Autonomous Car (address 7) and of the Pace
Car (address 8) can be displayed at the Position Tower. This func-
tion can be activated at the Control Unit. Therefore switch o the
Control Unit and keep the “BRAKE” button
pushed, g.
,
switch on the racetrack and release the “BRAKE” button again. By
pushing the button again the function may be changed:
1 LED lights = no display
2 LEDs light = display at the Position Tower
Set the function requested and conrm your choice via “START/
ENTER”.
On/o switch
Switch for fuelling function
Button to start the race / acknowledge programming
Button for Pace Car / termination of programming
Button for setting basic speed
Button for setting braking performance
Button for setting fuel tank capacity
Programming button for cars

Some buttons are assigned with dierent tasks. In order to set a
function you need to use key combinations. Any programming steps
can be cancelled with button
“ESC/PACE CAR″. You will nd
further details in the course of this manual.
Connections (from left to right):
Connection for Lap Counter 30342
Connection for PC-Unit
Connector 1 for speed controller, speed controller extension set
or Wireless-Tower
Connector 2 for speed controller or second Wireless-Tower
Connector 3 for speed controller
Connector 4 for speed controller
Connection for DIGITAL 124 / DIGITAL 132 power supply

As far as a Wireless Tower is used, it will have to be plugged into
connector 1. Alternatively a second Wireless Tower can be plugged
into connector 2. In case only one Wireless Tower is used, connec-
tor 2 will have to be kept empty.
Additional wired speed controllers may be plugged into connectors
3 and 4. Please note that these will use address 5 and 6 then.
Using the speed controller extension set 30348 it has to be plugged
into connector 1. The cars´ addresses will be allocated as follows:
• Speed controller extension set = address 1, 3 and 4
• connector 2 = address 2
• connector 3 = address 5
• connector 4 = address 6
4


Need help? Post your question in this forum.

Forumrules
1

Forum

carrera-digital-124---30352-control-unit

Reset search

  • can i get a copy of the carrera eb control display panel Submitted on 22-5-2022 at 20:52

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera Digital 124 - 30352 Control Unit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera Digital 124 - 30352 Control Unit in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info