424242
81
Zoom out
Zoom in
Previous page
1/87
Next page
79Appendix
Appendix
For your safety (Australia only)
To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin
power point which is effectively earthed through the normal household wiring.
Extension cords used with the equipment must be three-core and be correctly wired to provide
connection to earth. Wrongly wired extension cords are a major cause of fatalities.
The power point shall be located near the equipment and shall be easily accessible.
The fact that the equipment operates satisfactorily does not imply that the power point is earthed and
the installation is completely safe. For your safety, if in any doubt about the defective earthing of the
power point, consult a qualified electrician.
Caution (New Zealand only)
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has
accepted that the item complies with the minimum conditions for connection to its network. It
indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above
all, it provides no assurance that any item will work correctly in all respects with another item of
Telepermitted equipment of a different make or model, nor does it imply that any product is
compatible with all of Telecom's network services.
This equipment may not necessarily provide for the effective hand-over of a call to or from a
telephone connected to the same line.
The operation of this equipment on the same line as telephone or other equipment with audible
warning devices or automatic ring detectors will give rise to bell tinkle or noise and may cause false
tripping of the ring detector. Should such problems occur, the user is not to contact Telecom Faults
service.
Should this equipment become physically damaged, disconnect immediately from the Telecom
connection and power source and contact your nearest service agent.
To relocate the equipment, please:
(1) Disconnect the equipment from the Telecom connection.
(2) Disconnect the equipment from the power source.
(3) Reconnect the equipment to the power source.
(4) Reconnect the equipment to the Telecom connection.
If the supply cord of this equipment is damaged, it must be replaced by the special cord (Parts NO.:
HH2-1910).
Telepermitted equipment only may be connected to the auxiliary telephone port. The auxiliary
telephone port is not specifically designed for 3-wire-connected equipment. 3-wire-connected
equipment might not respond to incoming ringing when attached to this port.
This device may be subject to bell tinkle, or mistakenly enter receive mode when calls are made
from another device on the same line. If this occurs, the problem should not be referred to the
Telecom Faults service.
Please note when you connect an extension phone to this device, if you use an extension phone
which has features such as “last number redial,” redial memory numbers may be lost.
Note
Decadic Dialing is not available in Australia.
81


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon fax jx 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon fax jx 500 in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info