637183
3
Zoom out
Zoom in
Previous page
1/6
Next page
2012 IQ300 Computer
Setup and Owners Manual - 11/11
TROUBLESHOOTING
CONDITION ACTION
Wheel moving but current speed does not
appear
Check/adjust sensor and magnet gap.
Battery is low –> replace
“ERR01” appears on display Battery low –> replace
“ERR” appears on display
Interference from another electronic
device-> turn o or move electronic
device
Display is blank, very light or black Battery low –> replace.
Computer too hot –> move to cool area.
Display changes slowly
Computer too cold –> move to warm
area
NOTE: Touch feature is activated by nger pressure. If gloves are to thick, such
as winter gloves, the FUNCTION button may not be activated and require more
pressure.
NOTE: The computer uses a pencil tip sized free-oating sensor for auto on/o
features. If you hear a rattling noise during excessive vibration, it is normal and
the function will not be eected.
IQ300 Specications
Operating Temperature 0° C ~ 40° C, ( 32° F ~ 104°F)
Storage Temperature -10° C ~ 50° C, ( 14° F ~ 122°F)
Battery 3 volt lithium, CR2032 cell
Weight 30.6 grams
Timer Range: 0~29 (hour): 59 (minute): 59 (second)
Current Speed Range: 0 ~ 99.9 KM/ 0~62 Mile
Average Speed Range: 0 ~ 99.9 KM/ 0~62 Mile
MAX Speed Range: 0 ~ 99.9 KM/ 0 ~ 62 Mile
(Trip) Distance Range: 0 ~ 999.99 KM/ 0~600 Mile
Odometer Range: 0 ~ 99999 KM/ 0 ~ 62000 Mile
SETTING CALORIES BURNED KCAL
This computer can estimate calories burned while riding. The estimate is based on weight,
gender, time ridden and average speed. IMPORTANT: The estimate is truly an estimate.
Actual calories burned will vary depending on many variables the computer does not
calculate such as heart rate.
1. Press FUNCTION until the KCAL displays.
2 Press and hold SET for >3 seconds to begin programming.
3. Press SET to select gender MALE or “FEMALE”.
4. Press FUNCTION to store gender.
5. Press SET to change weight unit “Kg” or “Lb.
6. Press FUNCTION to begin entering your weight in unit selected.
7. Press or hold Set to change the weight. Range: 0 ~ 150 Kg, 0-330 Lb.
8. Press and hold the Function for 3 seconds to exit programming.
RESETTING THE ODOMETER ODO
If the battery is replaced, it is possible to update the odometer to the mileage on your bike
after replacing the battery.
1. Press FUNCTION until the ODO displays.
2. Press and hold SET for >3 seconds to begin programming.
3. Press FUNCTION until “00000 (ve zeros) and ODO appears on the screen
4. Press SET to change the appropriate numbers. Press FUNCTION to change cursor
position.
5. Repeat step 4 until the odometer is set.
6. Press and hold FUNCTION for 3 seconds to exit programming.
BATTERY REPLACEMENT
Remove the computer from the handlebar mount. Use a coin to unscrew the battery door.
Turn counter-clockwise. Remove the old battery. Place a new battery (CR2032) into the
computer with the positive “+” marking of the battery facing up. Replace the battery door.
Follow these steps for replacing the sensor battery (CR2032).
CANNONDALE USA
Cycling Sports Group, Inc.
172 Friendship Road,
Bedford, Pennsylvania, 15522 , USA
(Voice): 1-800-BIKE-USA
(Fax): 814-623-6173
custserv@cyclingsportsgroup.com
CANNONDALE EUROPE
Cycling Sports Group Europe, B.V.
mail: Postbus 5100
visits: Hanzepoort 27
7570 GC, Oldenzaal, Netherlands
(Voice): + 41 61.4879380
(Fax): 31-5415-14240
servicedeskeurope@cyclingsportsgroup.com
CANNONDALE AUSTRALIA
Cycling Sports Group Australia Pty Limited
Unit 8, 31-41 Bridge Road
Stanmore, NSW 2048, Australia
(Voice): 61-2-85954444
(Fax): 61-2-85954499
cannondale@cyclingsportsgroup.com.au
CANNONDALE JAPAN
Namba Sumiso Building 9F,
4-19, Minami Horie 1-chome,
Nishi-ku, Osaka 550-0015, Japan
(Voice): 06-6110-9390
(Fax): 06-6110-9361
cjcustserv@cannondale.com
CANNONDALE UK
Cycling Sports Group
Vantage Way, The Fulcrum,
Poole, Dorset, BH12 4NU
(Voice): +44 (0)1202 732288
(Fax): +44 (0)1202 723366
sales@cyclingsportsgroup.co.uk
CANNONDALE CONTACT INFORMATION
PROGRAMMING THE SENSOR
NOTE: These steps are only required if using the computer with a 2nd bike and only need
to be done once. Complete these steps after the computer is programed and the sensor
is installed.
1. Install the computer on Bike 2.
2. Press the blue SENSOR PROGRAMMING BUTTON on the back of the SENSOR INDICATOR
LED ashes. Release the button.
3. Lift the front wheel o the ground and spin it. The bike 1 icon will switch to the bike
2 icon “ and begin recording information for bike 2.
4. Verify nal set up for bike 2 by pressing the blue SENSOR PROGRAMMING BUTTON.
The LED will ash twice for bike 2.
5. To verify nal set up for bike 1, reinstall the computer on bike 1. Lift and spin the
front wheel to start the computer. Stop the wheel then press the blue SENSOR
PROGRAMMING BUTTON The SENSOR INDICATOR LED will ash 1 time to verify proper
function with bike 1.
SENSOR
PROGRAMMING
BUTTON
SENSOR
INDICATOR LED
SETTING THE TEMPERATURE
1. Press FUNCTION until ODO displays.
2. Press and hold SET for >3 seconds to begin programming.
3. Press FUNCTION repeatedly until TEMP” displays.
Press SET to change Fahrenheit (F) or Celsius (C)
4. Press and hold FUNCTION for 3 seconds to exit programming.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cannondale IQ300 - 2012 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cannondale IQ300 - 2012 in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info