109750
3
Zoom out
Zoom in
Previous page
1/16
Next page
when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops
after 5’ (the pilot lamp flashes). Button E: drives the motor in fourth speed (the corresponding pilot lamp comes on);
when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and thus the motor stops
after 5’ (the pilot lamp flashes).
Pay special attention to the grease filters: if the model purchased has the controls shown in Figure 12: the
grease filters must be cleaned approximately once every 30 hours of operation (when the central segment on the
display goes on or starts blinking). To remove the filters: press inward on the clamps at the handles and pull the
filter downward. Wash out the filter using a neutral soap. Once the cleaned filters are reinstalled, keep button R
(Reset) pressed for two seconds to reset the counter. For further information, see the Controls in Fig. 12 in the
paragraph entitled “Operation”. If the model purchased has the controls shown in Figure 10/11: the grease filter must
be cleaned periodically: exactly how often depends on use (at least once every other month). To remove the filter:
push inward on the clamp at the handle and pull the filter downward. Wash out the filter using a neutral soap. If the
model purchased has the controls shown in Figure13: the grease filters must be cleaned approximately once every
30 hours of operation (when the light button lamp comes on) - Fig. 13S). To remove the filters: press inward on the
clamps at the handles and pull the filter downward. Wash out the filter using a neutral soap. Once the cleaned filters
are reinstalled, to reset the counter hold the light button pressed down for about 1” (Fig.13A) while the corresponding
pilot lamp (S) is on. For further information, see the Controls in Fig.13 in the paragraph entitled “Operation”.
Charcoal filter/s: if using the hood in the filtering hood, the charcoal filter must be replaced periodically. To
remove the charcoal filters, proceed as follows, depending on the model purchased:
- if the hood features round charcoal filters (Fig. 14), remove the charcoal filter by turning clockwise.
- if the hood features a panel type charcoal filter (Fig. 9), remove the charcoal filter by first of all removing the two
filter retainers M.
If the model purchased has the controls shown in Figure 12, the charcoal filters must be replaced whenever the
central segment of the display starts blinking (i.e. every 120 hours of operation). If the model purchased has the
controls shown in Figure 10/11, the charcoal filters must be replaced according to use: on the average once every
6 months. If the model purchased has the controls shown in Figure 13, the charcoal filters must be replaced each
time the light button (Fig.13S) lamp flashes (i.e. every 120 hours of operation).
To gain access to the incandescence bulbs, remove the grease filters as described above and remove the
bulbs. Replace with lamps of the same type.
If the halogen lamps need changing, slacken the ring nut in an anticlockwise direction and remove the bulb itself
(Fig. 15). Replace with a bulb of the same type. CAUTION: Do not handle glass bulb with bare hands.
The motor used in this hood features a safety device (thermal cutout) that responds to temperature changes
For accidental reasons or due to installation faults, this device could engage and automatically shut off the
motor, thereby preventing serious damage to the equipment. In such cases, after allowing the motor to cool
down, the hood can be switched on again; the cause of the fault will nonetheless have to be remedied,
ensuring installation has been correctly made and that all the instructions in the Information sheet have been
complied with.
DEUTSCH
GERÄTEAUSFÜHRUNG
Das Gerät kann in Umluftversion und in Abluftversion geliefert werden. In der Umluftversion (Abb. 1) werden
die durch das Gerät geleitete Luft und der Dampf durch Kohlefilter gereinigt und dann über die seitlichen Lüftungsgitter
der Haube wieder in Zirkulation gebracht. ACHTUNG: Bei Verwendung der Umluftversion sind ein Kohlefilter und ein
Luftableitblech (A) notwendig, das in den unteren Teil des Rohrs eingebaut wird und ein erneutes Einleiten der Abluft
in den Raum ermöglicht. Die Kohlefilter werden nicht mitgeliefert. In der Abluftversion (Abb. 2) werden die Dämpfe
und Küchengerüche direkt über eine Evakuationsöfffnung in der Wand oder Decke nach außen abgezogen. Daher
sind keine Kohlefilter notwendig.
MONTAGE DES GERÄTS
Vor den Montageoperationen muß/müssen zur leichteren Handhabung des Geräts die Fettfilter entfernt werden:
Den Festhalter in der Nähe des Griffs nach innen drücken und den Filter nach unten ziehen (Abb. 3).
Befestigung an der Wand (Abb. 4): Benutzen Sie die Bohrschablone, um die Dübel in der Wand anzubringen,
wobei der Abstand zwischen der Haube und dem Kochfeld mindestens 65 cm betragen muß. Nun kann das Gerät
mit den Schlüssellochöffnungen in der Geräterückwand in die Schrauben eingehängt werden (A). Zusätzlich wird das
Gerät durch die Sicherungslöcher fest mit der Wand verschraubt (B). Um das Gerät nicht zu beschädigen, dürfen nur
die vom Hersteller vorgesehenen Bohrungen benutzt werden.
Befestigung der Teleskoprohre: Mindestanforderungen für die Montage: – Stromversorgungsanschluß innerhalb
der Außenabmessungen des Teleksoprohres vornehmen. – Wenn Ihr Gerät als Abluftversion installiert wird, ist ein
Loch zur Abführung der Luft vorzusehen.
Positionieren Sie die Halterung (W) 50 mm von der Decke entfernt, vertikal oberhalb der Haube unter Zuhilfenahme
der Schlitze in der Mitte der Halterung (Abb. 5). Markieren Sie mit einem Filzstift die beiden Bohrlöcher an der Wand.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Candy CCE 19 X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Candy CCE 19 X in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info