656765
8
Zoom out
Zoom in
Previous page
1/13
Next page
8
1
Standby/On button
Controls the standby state of the unit. When the LED is illuminated
red, the system is in its low power standby state. When the unit is
rst turned on it takes approximately 20 seconds to fully power up
and become active. During this phase the LED will blink red on and
o .
2
Volume buttons
Controls the player's volume.
3
Mute button
Press to mute and press again to un-mute the unit.
4
AUX Button
Selects AUX/MP3 inputs. Pressing this button will toggle between
Aux and MP3 inputs.
5
Bluetooth button (Pairing)
Used to pair (connect to) Bluetooth devices so that they can be
played back wirelessly. When the button is pressed the LED on the
unit will blink blue for approximately 30 seconds. This indicates that
the system is in pairing mode. See later section.
6
Presets buttons 1 – 10
Press to recall an internet radio preset. As shipped from the factory
10 stations will have been pre-assigned, 5 can be accessed from
the top panel buttons, all 10 can be accessed via the remote. To
change the assigned stations use the free Air App for Android or
Apple devices, see later section.
7
Bass controls
Allows setting of the bass/low frequency response of the unit tailored
to your taste and the acoustics of your room.
Getting started
1
4
Bass +
5
8
6
32
7
10
9
Remote control
Note: If you make a mistake during the connection process, reset
the Air. To do this, press and hold the Standby/On button and WPS
button on the rear panel for 10-15 seconds until the Air switches o,
then repeat the connection process.
Network connections
Before you can use your Air for Internet Radio/Streaming you must
have the following:
A broadband internet connection (such as ADSL) to a suitable
internet service provider (ISP).
A network connection either wirelessly via 802.11b/g or n Wi-Fi
or wired Ethernet connection (10 or 100 M bits/sec via an RJ45
connection).
If your wireless network is congured to use Wired Equivalent Privacy
(WEP) or Wi-Fi Protected Access (WPA) data encryption then you
will need to know your WEP or WPA key so you can get the Air to
communicate with the network.
IMPORTANT:
Before you continue, make sure that your wireless access point
or router is powered up and working with your broadband internet
service (use your computer to verify this). To get this part of the
system working you must read the instructions supplied with the
wireless access point or router.
The Air can be congured to connect to a wired or wireless network.
For wired setup, see later section 'Connecting to a wired network'.
Connecting to a wireless network
1. Connect the Air to the mains power and press the button on
top of the unit. Wait for up to 20 seconds for the ashing light on
the rear panel to ash green
and orange . If the light does
not ash green and orange after 20 seconds, please carry out a
factory reset as detailed above, and start again.
Apple Wireless Accessory Conguration
If you have an Apple mobile device, go to the 'Settings -> Wi-Fi'
menu. Choose the Air showing under 'Set up New AirPlay Speaker'
and follow the instructions.
Note: For Mac with OS X, once connected the setup will then
proceed to Airport utility. Follow the instructions.
Otherwise, proceed to the next section.
12
3 4 5
7
6
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cambridge Audio Air 100 V2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cambridge Audio Air 100 V2 in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cambridge Audio Air 100 V2

Cambridge Audio Air 100 V2 Quick start guide - English - 2 pages

Cambridge Audio Air 100 V2 User Manual - German - 13 pages

Cambridge Audio Air 100 V2 User Manual - French - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info