306739

Calor 5033 alte rn prog Manual

17
Zoom out
Zoom in
Previous page
1/20
Next page
English
1 - DESCRIPTION (see exploded view) :
Your machine is composed of:
2 - SAFETY INFORMATION
Voltage:
•
Models 50.23, 50.27 and 50.33: 220-240 V
•
Model 50.40: 230 V
•
Model 50.24 is dual voltage (115-127 V or 220-240 V).
•
Always make sure the voltage displayed at the back of the washing machine is appropriate for your power supply. If not, push the
toggle switch all the way to one side until the correct voltage is displayed.
•
ALWAYS CONNECT MODEL 50.40 TO A GROUNDED (THREE-HOLE) SOCKET.
A plastic tub (A) which has:
•
1two water level marks: the low water mark (1) indicates the
lowest acceptable water level for any size load (always fill to this
mark even if the load is small) and the high water mark (2)
indicates the highest level (water plus laundry) to which the
machine may be filled. It is important to use the right proportion of
water for the amount of laundry otherwise the laundry may not be
agitated vigorously enough,
•
1a drain orifice (3) at the bottom right of the machine to drain
water from the tub,
•
1an emptying system controlled by a drain handle (4) on the top
right of the machine.
In addition, on Model 50.40:
•
1A heater (5) on the left of the
machine with a three-prong plug, an overheat switch and a floater to
p r event heater operation when the water level in the tub is too low
•
1An opening at the top centre of the machine to discharge water
during rinsing.
An easy-to-remove washing unit (B) which has:
•
1a rotor plate (8) and roller track (7),
•
1a roller ring with six rollers (9),
•
1a rotor (10), the large rotating plate under the tub; the
shape of the raised cross on the rotor has been designed
specifically for gentle washing by combining a slow tumble
and alternating spin motion,
•
1a partition (11) to isolate the drive shaft (12) and pinion
(13).
A motor unit (C), which has:
•
1a motor with overheat protection that stops the motor in case of
accident, overheating or incorrect positioning; the motor will start
once parts have cooled (which may take up to 15 minutes),
•
1a power cord storage cassette.
In addition, on Models 50.23, 50.24, 50.33 and 50.40:
•
1a timer (16) and timer display (15) to automatically stop the
machine after the desired wash time.
On model 50.40:
•
1an ON/OFF switch (17) for the heater.
On Model 50.27:
•
1an automatic programmer (16) and programmer display (15) to
select any of three wash cycles,
•
1pre-wash ;
•
1soak or ;
•
1wash and single, double or triple rinse;
the machine stops automatically once the selected cycle is
complete.
A lid (D) with viewing window (window not on all models).
A fill hose (E) and hose end-piece (F).
Important:
•
Never operate the washing machine unless it contains sufficient water.
•
Unplug the washing machine before removing the motor unit.
•
Never fill the tub with flammable liquid.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Calor 5033 alte rn prog at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Calor 5033 alte rn prog in the language / languages: English, Dutch, French, Spanish as an attachment in your email.

The manual is 0,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info