ENGLISH
3
ENGLISH
2
DISC PLAY
PRECAUTIONS
• Use only in a 12-volt DC negative-ground electrical system.
• Disconnect the vehicle's negative battery terminal while mounting and connecting the
unit.
• When replacing the fuse, be sure to use one with an identical amperage rating.
•Using a fuse with a higher amperage rating may cause serious damage to the unit.
•DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dan-
gerous to the eyes.
• Make sure that pins or other objects do not get inside the unit; they may cause mal-
functions, or create safety hazards such as electrical shock or laser beam exposure.
• If you have parked the car for a long time in hot or cold weather, wait until the tem-
perature in the car become normal before operating the unit.
• Keep the volume at a level at which you can hear outside warning sounds (horns
sirens, etc.).
CD NOTES
• Playing a defective or dusty CD can cause dropouts in sound.
• Hold CDs as illustrated.
• DO NOT touch the unlabeled side.
• DO NOT attach any seal, label or data protection sheet to either side of a disc.
• DO NOT expose a CD to direct sunlight or excessive heat.
• Wipe a dirty CD from the center outward with a cleaning cloth.
•Never use solvents such as benzine or alcohol.
• This unit cannot play 3-inch ( 8cm ) CDs.
• NEVER insert a 3-inch CD contained in the adapter
or an irregularly shaped CD.
• The unit may not be able to eject it, resulting in a
malfunction.
BEFORE OPERATION
•DO NOT raise the volume level too much, as this
will block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operation.
CAUTION
DO NOT open covers and do not repair by yourself.
Consult the dealer or an experienced technician for help.
Installation procedures
First complete the electrical connections, and then
check them for correctness.
Anti-Theft System
This unit is equipped with a detachable panel.
Removing this panel makes the radio totally inoperable.
Removing the panel
1. Switch off the power of the unit.
2. Remove the detachable panel.
3. Gently press the button of the case and open the
cover. Place the panel into the case and take it with you
when you leave the car.
Install detachable panel
1.Fix right part of face plate in the right part of panel slot
of the unit.
2.Press down the left side of the face plate until it clicks
into the panel slot of the unit.
Remove the unit
Switch of the power of the unit.
1. Remove the panel and the trim plate.
2. Insert both T-Keys into hole in front of the set until
they lock.
3. Pull out the unit.
5. BASIC OPERATIONS
1) PANEL REMOVE BUTTON
Press this button to remove the control panel.
2) POWER ON/OFF BUTTON
Press POWER button or any other button on the front of the radio (except
Open/Eject)to turn the unit on. Press POWER button again to turn the unit off.
18) MODE BUTTON (MODE)
Press MODE button to select a different mode of operation as indicated on the display
panel.Available modes include Tuner, CD, MP3 and Aux in mode .
10) MUTE BUTTON (MUTE)
Press the mute button momentarily to mute the audio volume, and "Mute" will flash in
the display. Press the mute button again to restore volume to the previous setting.
12) VOLUME KNOB
To increase the volume rotate the volume knob clockwise,to decrease the volume rota-
te the volume knob counterclockwise.
13) AUDIO BUTTON (AUDIO)
Press the AUDIO button, the display will be displayed first option is Volume, followed by
Bass,Treble, Balance, Fader and back to Volume.
When adjusting audio functions, the unit will automatically exit audio control mode
after 5 seconds of inactivity. Use the volume knob to adjust the settings.
Press the AUDIO button for more than 3 seconds, the display will be displayed as cycli-
cal mode of following functions:TA SEEK or ALARM, PI SOUND or MUTE, RETUNE L
or S, MASK DPI or ALL, BEEP 2’nd and ALL or OFF.
TA SEEK or ALARM
Rotate the knob to choose TA ALARM or TA SEEK mode,When TA is turned on and
no traffic program identification code has been received during the specified time, no
TA/TP is displayed and according to the MENU SELECT, alarm is set off, or TA SEEK is
activated.
TA ALARM mode: NO TA/TP is displayed and alarm is set off.
TA SEEK mode:TA SEEK is activated.
PI SOUND or MUTE
PI SOUND:When above different PI sound (DIP) is heard once in a while, the DIP’s
sound will be heard for less than 1 second.
PI MUTE:When above different PI sound (DIP) is heard once in a while, a mute sound
will be heard for less than 1 second.
RETUNE L or S
The initial time of automatic TA search or PI search mode is selected.When PI infor-
mation is not caught for retune time, the radio start to retune to the next same PI
station.When the same PI station does not catch 1 cyclic search, the radio start to
retune to the next same PI station.
RETUNE L mode: Selected as 90 seconds
RETUNE S mode: Selected as 30 seconds
MASK DPI or ALL
Rotate the knob to choose MASK DPI or MASK ALL mode.
MASK DPI mode: Only the AF which has different program identification is masked.
MASK ALL mode:The AF which has different program identification and NO RDS sig-
nal with high field strength is masked.
BEEP 2’ND,ALL or OFF
BEEP 2’ND mode:The beep is only generated when an allottes double key is pressed
long (1 sec.).
BEEP ALL mode:The beep is generated when every key is pressed.
BEEP OFF mode:The beep is off.
9) DISPLAY (DISP)
Pressing the “DISP” key will display the following modes;
In case of receiving a RDS station:
Tuner mode PS – CT – FREQ – PTY
CD/MP3 player mode CDP – CT – PS – FREQ – PTY
In case of receiving NON RDS station
Tuner mode NO CLOCK – FREQ – NO PTY
CD/MP3 player mode CDP – CT – FREQ – NO PTY
6. TUNER OPERATION
6) BAND/LOUDNESS BUTTON (BAND/LOUD)
Press BAND to change between FM 1, FM 2, FM 3 and MW.
Press BAND for more than 2 seconds to start loudness.
19) TUNING UP/DOWN BUTTON
Manual Tuning
Press the Up Tuning or Down Tuning button for more than 3 seconds to move the radio
frequency number up or down one step.
Auto Seek Tuning
Press the Up Tuning or Down Tuning button for less than 3 seconds to move to next
station automatically.
