165940

Caliber cx 2 r crossover Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
1
1. Low-Pass frequency selector. By using this
selector you can choose the Low-Pass crossover
point (50/80/100/120Hz)
2. High-Pass frequency selector. By using this
selector you can choose the High-Pass crossover
point (80/100/120/140Hz)
3. Level Controls. Since the volume of each output
varies upon speaker efficiency variation and main
amplifier output variation, make adjustments using
these controls.
4. Phase switch.Allows you to change the phase of
your subwoofers from 0° to 180° to help compen-
sate for timing differences between speakers.
5. Mode switch.Allows you to change the subwoof-
er output between stereo and mono, thus facilita-
ting single subwoofer installations.
6. Input jacks. Input from sound source RCA jacks.
7. High level input. Input from sound source’s spea-
ker leads.
8. Low Pass output jacks. Connect RCA cables to
the subwoofer amplifier.
9. High Pass output jacks. Connect RCA cables to
the Mid-High amplifier.
10. Power connector port. B+ :Connect to the (+)
positive terminal of the car battery. Place a fuse
close to the car battery to protect the vehicle.
GND: Connect to a metal part of the car, or nega-
tive (-) terminal of the car battery.
REM:Connect to the remote activating wire of the
radio, or Power antenna wire.
Input
LR
Sub-Woofer
OutLR
High-Pass
OutLR
50 Hz
100 Hz
80 Hz
Mode
Sub-Woofer
Output Level
Min
Max
High-Pass
Output Level
Min
Max
Stereo
Mono
Phase
Reverse
Normal
120 Hz
140 Hz
100 Hz
120 Hz
80 Hz
Power
GND RB+
7 1 2
3
4
5
6
8
9 10
CX2
CX2
2-Way 18dB/Oct Electronic Crossover
High Level Input
This diagram shows you a typical configuration. Two
power amplifiers are required. The Low-Pass output
drives the subwoofers amplifier and the High-Pass out-
put drives a second amplifier for your midrange-/twee-
ter system. They could also be full range speakers
except now they are relieved of their deep bass duty
which is carried entirely by the subwoofers.
Full frequency performance is accomplished by the two
groups working together without any overlaps or gaps.
One speaker pair picks up as the other is falling off.The
cut-off frequency for each can be set independently with
the multi-position switches.In most cases they should be
set close to the same frequency to avoid unintentional
peaks or valleys in the system response. This common
cut-off frequency is called the “crossover frequency”.
Connections
Make connections according to the diagram and note
the following:
1. Make all connections securely and avoid stretching
any wires or cables that could pull loose later on.
Never make or break any connection with the power
to your amplifier turned on.
2. Make sure the ground connection attaches to bare
metal that is part of the car’s chassis and not a insu-
lated piece of trim.If you experience excessive noise
during operation, its cause will probably trace back
to a poor ground connection.
3. Make all connections to the CX2 before mounting.
4. Disconnect the car battery to prevent short circuits
while making power connections. Insulate all con-
nections to prevent short circuits.
5. Plug the radio’s pre-out RCA plugs into the CX2’s
input jacks, or connect the radio’s speaker outputs
to the High level input on the Molex connectors and
plug into item 7.Do not use both RCA-input and
High Level input at the same time.
Low-Pass
Audio
Signal
Source
Right
Left
High-Pass
CX2
CX2
Power
Amplifier
Power
Amplifier
2
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber cx 2 r crossover at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber cx 2 r crossover in the language / languages: English as an attachment in your email.

The manual is 0,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info