The CADAC Patio BBQ is designed for outdoor cooking enthusiasts, which makes it ideal for patio entertaining.
The ease of use and the versatility of the interchangeable grills allow for a variety of cooking methods, whether you are entertaining a crowd or barbecuing for two.
The BBQ Grid is ideal for barbecuing cuts of meat, kebabs, vegetables, chicken or fish.
The Reversible Grill Plate is ideal for traditional breakfasts, stir-fries, pancakes, etc.
The Warming Rack expands the cooking area and is great for warming breads and cooking jacket potatoes or stuffed vegetables. (Only available on certain models)
The Side Burner is ideal for cooking food or making a sauce while barbecuing.
The hose and seal on the regulator must be checked for wear ordamage before every use and before connecting to the gas cylinder (See Fig. 1).
Do not move the appliance during use.
Ensure the appliance is used away from flammable materials. Minimum safe distances are 1,2m above the appliance and 600mm to the rear and sides of the appliance (See Fig. 2).
Do not use an appliance that is damaged, leaking or which does not operate properly.
Ensure that the gas cylinder is connected or changed in a well ventilated area, preferably outdoors, away from any source of ignition such as open flames, and away from other
people.
Keep gas cylinders away from heat and flames. Do not place on a stove or any other hot surface.
Ensure that the assembled unit is stable and does not rock.
Do not cover or change the primary air supply apertures in the burners as this will affect the performance of the product and may lead to an unstable flame.
In the event of burn back, where the flame burns back and ignites at the jet, immediately turn off the gas supply by first closing the control valve on the gas cylinder and then the
appliance valve.After the flame is extinguished remove the regulator and check the condition of its seal, replace the seal if in doubt.Also check that the jet is not blocked. Replace if
in doubt. Re-light the appliance as described in Section 6. Should the flame light back persistently, return the product to your authorised CADAC repair agent.
If there is a leak on your appliance (smell of gas), turn off the gas supply, first at the control valve on the cylinder and then on your appliance by turning the control knobs fully
clockwise.
If you wish to check for leaks on your appliance, do it outside. Do not try to detect leaks using a flame. The correct way is tosmear the joint with soapy water. If bubbles form, then
there is a gas leak. Immediately turn off the gas supply firstly by closing the control valve on the gas cylinder and then the appliance valves. Check that all the connections are
properly fitted. Re-check with soapy water. If a gas leak persists return the product to your CADAC dealer for inspection / repair.
Do not modify the appliance or use it for anything for which it has not been designed.Any modification of the appliance may be dangerous.
During use, part of the appliance will become hot, particularly the cooking areas and the hood.Avoid touching hot parts with your bare hands. The use of oven gloves is
recommended.
Keep young children away from the appliance at all times.
This appliance consumes oxygen and needs ventilation for optimum performance and for the safety of those in close proximity.
Do not twist or pinch the hose. Ensure that it is routed away from the BBQ body so as to prevent deteriation / damage to the hose caused by heat.
Fit one end of the low pressure hose onto the regulator nozzle and theother end onto the Patio BBQ nozzle by pushing it on as far as possible. Ensure the O’Ring is present, in good
condition & fitted properly. Do not use the appliance without the O’Ring fitted. Firmly clamp hose into position using a hose clamp at both ends of the hose (See Fig.1&3).
Ensure that the connections are made securely and do not allow gas to leak. Check for gas leaks before using the Patio BBQ. Ensure that the appliance control valves are in the off
position by turning the knobs fully clockwise to their stop (See Fig. 4).
Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator is in position and in good condition. Carry out this check each time you fit the
appliance to a gas cylinder (See Fig. 1).
Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
Hang the cylinder on the cylinder bracket situated on the side of the trolley.
Ensure that the gas cylinder is fitted or changed in a well ventilated location outdoors, away from any source of ignition such as naked flames, and away from other people.
Make sure that the gas cylinder is kept upright at all times. Screw the regulator onto the cylinder until it is fully engaged. Hand tighten only.
If there is a leak on your appliance (smell of gas), extinguish all sources of ignition in the vicinity of the appliance. If you wish to check for leaks on your appliance, use soapy water
which is applied to the joints.Aformation of bubbles will indicate a gas leak. Check that all the connections are securely fitted and re-check with soapy water. If you cannot rectify the
gas leak, do not use the appliance. Contact your local CADAC stockist for assistance.
When changing a gas cylinder, first close the cylinder valve and then the appliance valve, making sure the flame is extinguished, unscrew the regulator. Re-fit the regulator to a full
cylinder following the same precautions as described above.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Cadac 98348 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Cadac 98348 in the language / languages: English as an attachment in your email.
The manual is 0,46 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
