684202

Cadac 98251 - Entertainer Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
33
4. Fitting and Changing the Gas Cylinder
• Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator is in position and in good condition.
• Carry out this check each time you  t the appliance to a gas cylinder (see  g. 1).
• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
• Ensure the gas cylinder is  tted or changed in a well ventilated location preferably outdoors, away from any source of ignition such as
naked  ames, and away from other people.
• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.
• If there is a leak on your appliance (smell of gas), extinguish all sources of ignition in the vicinity of the appliance. If you wish to check
for leaks on your appliance, use soapy water which is applied to the suspected area. A formation of bubbles will indicate a gas leak.
Check that all the connections are securely  tted and re-check with soapy water. If you cannot rectify the gas leak, do not use the
appliance. Contact your local CADAC stockist for assistance.
• When changing a gas cylinder,  rst close the cylinder valve and then the appliance valve, making sure the  ame is extinguished and
unscrew the regulator. Re- t the regulator to a full cylinder following the same precautions as described above.
• After the appliance has been fully assembled, perform a gas leak test before operating the appliance.
• Make sure that the gas cylinder is kept upright at all times. Hand tighten the regulator onto the cylinder until it is fully engaged.
5. General Maintenance
• There are no predetermined maintenance intervals for this appliance.
• It is dangerous to use an appliance with a cracked or perished seal and/or hose. Inspect both seals and hose regularly and replace if
they are not in order before using the appliance.
• If the appliance was in use it will be hot. Allow to cool suf ciently before attempting any maintenance.
• CADAC Patio BBQ’s are  tted with spesi c CADAC jets to regulate the correct amount of gas. Should the hole in the Jet become
blocked this may result in a small  ame or no  ame at all. Do not attempt to clean the Jet with a pin or other such device as this may
damage the ori ce, which could make the appliance unsafe.
5.1. Replacing a Blocked Jet
• Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder.
• Remove the grill plates. Remove the  ame tamers to expose the burners. Remove the retaining screws of the affected burner.
• Remove the affected burner by lifting it out of its location taking care not to damage the control valve whilst doing so. This will expose
the Jet.
• Unscrew the blocked Jet with a suitable spanner and replace it with a new Jet. Do not use pliers on the Jet as they can cause damage,
making the Jet unusable or impossible to remove.
• Do not over tighten as this may damage the Jet. To re-assemble, reverse the above procedure.
3. Using the appliance
• Place the cylinder inside the cabinet in the space provided.
• Use this appliance only on a  rm level surface.
• Before use ensure that the drip cup/tray is in place.
• Make sure the gas cylinder is correctly  tted to the appliance.
• Ensure the cylinder control valve is in the open position.
• To light the appliance using the automatic igniter, push in and turn the control knob in an
anti-clockwise direction until spring resistance is felt. Hold the knob in this position for
3 – 5 seconds to allow the gas to  ow and then turn the knob fully anti-clockwise to the
HIGH position. This will cause the automatic lighter to light the burner. Should the burner
not ignite the  rst time, turn the control knob to the OFF position and wait 5 minutes,
repeat the process until the burner ignites.
• Note! All burners are  tted with an automatic igniter.
• Cross lighting: To light the burners using cross lighting, light the left burner as described
above.
• To light the remainder of the burners, simply turn their control knobs to the HIGH position
while ensuring that the lighting sequence is such that any burner to be lit up is directly
adjacent to a burner which is already burning.
• Manual ignition: To light the burners manually,  rst remove the cast iron grill plate and
the de ector plate directly underneath it. Ignite a match or  relighter and position it next
to the left hand burner. Turn on the gas supply to that burner only by pushing the control
valve in and turning it in an anti-clockwise direction. This will ignite the burner. Once the
burner is ignited, carefully replace the de ector plate and cast iron grill plate. You will
now be able to light the remainder of the burners as described in ‘Cross lighting’ above.
• Use the control knobs to adjust the individual burner  ame intensity to the desired level
by turning the knob anti-clockwise to decrease the  ame and clockwise to increase it (see
g.3).
• After use,  rst close the valve on the gas cylinder. When the  ame is extinguished, close
the burner control valves on the appliance by turning control knobs fully clockwise.
Fig. 3
Fig. 3
GB
503-0604 LEV7 (98250-31, 98250-33, 98251-43) Cadac Entertainer 3 & 4 - User Manual (EU & SA).indd 3 08/09/2017 11:56:20
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cadac 98251 - Entertainer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cadac 98251 - Entertainer in the language / languages: English as an attachment in your email.

The manual is 0,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cadac 98251 - Entertainer

Cadac 98251 - Entertainer User Manual - German - 6 pages

Cadac 98251 - Entertainer User Manual - Dutch - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info