558648
1
Zoom out
Zoom in
Previous page
1/2
Next page
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push.
2: Gently twist.
3: The backing plate will unclip.
1
Functions:
4 Selectable Melodies
1: Ding Dong (Repeat) 3: Alarm
2: Westminster 4: Ding Dong Ding
4
To select a melody for the Door Chime
1: Remove the Back Plate from the Bell
Push.
2: Press the Melody Select button.
3:The chime will play the newly selected
sound.
4: Press again to select the next melody.
Note: For Front/Back door setup, select a
different melody in one of the Bell Pushes.
CR2032
Adding Additional Chime/Bell Push:
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
2
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
3
1: Plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz.
2: Switch the socket on.
Beep
Beep
1: The Chime will ‘Beep Beep’.
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chime.
3: The Chime will ring to
confirm setup.
Note: Maximum of 2
Bell Pushes can be learnt to a
single Chime for Front/Back
4
Additional Bell Push
To add an additional Bell Push to the Door Chime kit
1: Unplug the Door Chime and wait for 10
seconds.
2: Plug the Door Chime into the Socket and
switch the socket on.
3: Press both Bell Pushes within 60 seconds, to pair
the additional Bell Push to the Chime.
4: Chime will ring to confirm setup, wait 60 seconds
for Chime to exit the learn mode before repressing the
Bell Push5.
5: For Front/Back door setup, select a different melody in one of the
Bell Pushes - See Melody Selection.
Note: Maximum of 2 Bell Pushes can be learnt to a single
Door Chime.
Front Door
Back Door
New Chime
Additional Chime
To add an additional Chime unit to the Door Chime kit
1: Unplug the NEW Door Chime and wait for 10
seconds
2: Plug the Door Chime into the Socket and switch the socket On.
3: The Chime will ‘Beep Beep’ to indicate that it has entered
the Learn mode.
4: Press the Bell Push within 60 seconds, to pair the additional
Chime to the Bell Push.
5: Chime will ring to confirm setup, wait 60 seconds for the Chime
to exit the learn mode before repressing the Bell Push.
Beep
Beep
BY103
1: Push Button 5: Plug-through Chime
2: Melody Selector 6: Speaker
3: Bell Push Battery
4: Signal Sent LED
1:
2:
4:
:3
6:
5:
3
Plug-in any standard electrical product,
220–240V ~50Hz.
e.g. table light, upto a Max Load of
1000W
Avoid using low voltage Transformers, as
this may reduce the operating range of
the Door Chime
Plug-through Socket:
Melody selection:
Plug-through
Wire Free Chime Kit
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Byron BY103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Byron BY103 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info