461156
10
Zoom out
Zoom in
Previous page
1/17
Next page
muraux, horizontaux et stable 500 L.) - La résistance avec éventuellement le corps de chauffe - Le joint
Le remplacement du corps de chauffe implique le remplacement de l’anode. Pour le 500L, le rempla-
cement de la résistance blindée implique la vidange du chauffe-eau et le remplacement du joint.
Toute opération de remplacement doit être effectuée par un professionnel avec des pièces d’origine
constructeur.
• Chauffe-eau stables : après coupure de l’alimentation électrique, le voyant vert ACI (1) continue de
clignoter (batterie 2,4 volts), aucun risque de choc électrique n’est à craindre.
Si le voyant ACI ne clignote pas, il faut procéder au remplacement du circuit électronique. Voir ci-des-
sous.
CHAUFFE-EAU VERTICAUX MURAUX
Le circuit électronique (2) fourni en SAV est préfixé sur le Tableau de bord.
Démontage :
• Couper l’alimentation du chauffe-eau
• Démonter le capot (1 vis) pour accéder aux parties électriques
• Déconnecter le fil d’anode rouge (4)
• Dévisser le fil noir (5) fixé sur la bride
• Dévisser la vis de fixation du bornier
• Dévisser les fils allant du bornier au thermostat, côté thermostat (7)
• Dévisser la vis de fixation du tableau de bord et déposer l’ensemble.
Remontage :
Procéder en sens inverse.
REMPLACEMENT DU CIRCUIT ELECTRONIQUE ACI VERVANGEN VAN HET ELEKTRONISCHE ACI CIRCUIT
WATERVERWARMERS VOOR VERTICALE WANDBEVESTIGING
Het elektronische circuit (2) dat door de na-verkoopdienst geleverd wordt, is reeds op zijn bedieningspaneel
bevestigd.
Om te demonteren :
• De waterverwarmer elektrisch afkoppelen.
• De beschermkap (1 Schroef) afnemen om toegang te krijgen tot de elektrische onderdelen.
• De rode draad van de anode (4) loskoppelen.
• De zwarte draad op de flens (5) losmaken.
• De bevestigingsschroef van de aansluitklem losdraaien.
• De draden die van de aansluitklem naar de thermostaat gaan, kant thermostaat (7), losmaken.
• De bevestigingsschroef van het bedieningspaneel losdraaien en het geheel afnemen.
Om terug te monteren : omgekeerd te werk gaan.
1- Voyant clignotant ACI (vert)
2- Circuit intégré ACI
3- Capot
4- Fil anode titane (rouge)
5- Fil de masse ACI (noir)
6- Raccordement du thermostat
Modèle “Tous courants” - Universele uitvoering
1- ACI knipperlampje (groen)
2- Ingebouwd ACI circuit
3- Beschermkap
4- Draad titaniumanode (rood)
5- Draad ACI aarding (zwart)
6- Aansluiting op de thermostaat
• De onderdelen die kunnen vervangen worden zijn : - thermostaat - anode (bij toestellen voor verticale
wandbevestiging, horizontale en staande uitvoeringen van 500 l) - weerstand met eventueel de warmte-
wisselaar - dichting.
Wanneer de warmtewisselaar vervangen wordt, dient de anode ook vervangen te worden. Bij de 500 l-uit-
voeringen vereist de vervanging van de gepantserde weerstand de lediging van de waterverwarmer en het
vervangen van de dichting.
Voor elke vervanging beroep doen op een vakman die gebruik zal maken van de oorspronkelijke wisselstuk-
ken afkomstig van de fabrikant.
• Staande waterverwarmers : na loskoppelen van de elektrische voeding blijft het groene ACI controlelamp-
je (1) knipperen (2,4 volt batterij), er is geen gevaar voor elektrische schok.
Indien het ACI controlelampje niet knippert, moet het elektronische circuit vervangen worden. Zie hieronder.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bulex RBE 10 S- 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bulex RBE 10 S- 6 in the language / languages: Dutch, French as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info