Manual Britax-Romer EVOLVA 1-2-3 SL SICT (page 1 of 2) (English)

767952

Zoom out

Zoom in

1/2

BRITAX RÖMER Kindersicherheit GmbH

Blaubeurer Strasse 71

D-89077 Ulm

Germany

T.: +49 (0) 731 9345-199/-299

F.: +49 (0) 731 9345-210

E.: service.de@britax.com

www.britax.eu

BRITAX EXCELSIOR LIMITED

1 Churchill Way West

Andover

Hampshire SP10 3UW

United Kingdom

T.: +44 (0) 1264 333343

F.: +44 (0) 1264 334146

E.: service.uk@britax.com

www.britax.eu

Please take the time to read these instructions carefully and keep them

to hand in the intended storage compartment 05 on the child safety seat at

all times! The instructions must be kept with the child safety seat if the latter

is passed on to a third party.

3. SAFETY NOTES

DANGER! For the protection of your child:

In the event of an accident at a collision speed of more than 10km/h, the child

safety seat may be damaged without the damage becoming immediately visible. In

this case, the child safety seat must be replaced. Please dispose of it properly.

• Always have your child safety seat checked if you suspect it may have been

damaged (e.g if it falls on the ground).

• Regularly check all important parts for damage. Ensure that all mechanical parts,

in particular, are fully functional.

• Never lubricate or oil parts of the child seat.

• Never leave your child unattended in the child seat in the vehicle.

• Only allow your child to enter and exit the vehicle on the pavement side.

• Protect the child safety seat from intensive direct sunlight when it is not in use.

The child safety seat can get very hot in direct sunshine. Children's skin is sensi-

tive and could be harmed as a result.

• The more snugly the belt ﬁts over your child's body, the better they will be protected.

Avoid putting thick clothes on your child under the belt.

• Take regular breaks on long journeys in order to give your child the opportunity to

run about and play.

• Use on the rear seat: Move the front seat far enough forwards to ensure that your

child's feet cannot hit the backrest of the front seat (to prevent risk of injury).

• If your child tries to open

the red ISOFIT safety button

or a buckle, stop the

vehicle as soon as it is safe to do so. Check whether the child safety seat is correctly

fastened and ensure that your child is correctly secured. Explain to your child the

dangers associated with their actions.

DANGER! For the protection of all vehicle occupants:

In the case of an emergency stop or an accident, unsecured persons or objects may

cause injury to other vehicle occupants. Please always check that:

• the backrests of the vehicle seats are locked, e.g. that a foldable rear seat bench

latch is engaged.

• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf) are

secured.

• all persons in the vehicle have their seat belts fastened.

• the child safety seat is always secured when it is in the vehicle, even if no child is

being transported.

WARNING! For your protection when handling the child seat:

• Never use the child safety seat free standing, not even for test sitting.

• To avoid damage, ensure that the child safety seat is not jammed in between

hard objects (car door, seat rails, etc.).

• Keep the child safety seat in a safe place when it is not in use. Do not place any

heavy objects on the seat and do not store it directly next to sources of heat or in

direct sunlight.

4. USE IN THE VEHICLE

Please observe the instructions for using children's restraining systems in the operating

instructions of your vehicle. The seat can be used in vehicles with ISOFIX anchoring systems

(see type list) and in vehicles with a 3-point belt.

To determine which seats are approved for use with child safety seats that meet the

requirements for weight classes 9 to 18 kg and 15 to 36 kg, please refer to the operating

instructions of your vehicle.

9-36 kg

The EVOLVA 1-2-3 SL SICT is approved for two dierent methods of installation:

Group Installation method Means by which child

is secured

Section of

user instructions

1 (9-18 kg) Vehicle belt With 5-point harness A

1 (9-18 kg) Vehicle belt + soft latch With 5-point harness A

2+3 (15-36 kg) Vehicle belt Vehicle belt B

2+3 (15-36 kg) Vehicle belt + soft latch Vehicle belt B

a) This means that the child safety seat may only be used in vehicles that are listed in the enclosed

vehicle type list. This type list is consistently kept up to date.

The latest version can be obtained from us or from www.britax.com

You can use your child safety seat as follows:

In the direction of travel Yes

Against the direction of travel No 1)

With 2-point harness No

With 3-point belt 2) Yes

with ISOFIX fastening points (be-

tween seat surface and backrest)

Yes

On front passenger seat

Yes 3)

On outer rear seat Yes

On centre rear seat

(with 3-point belt)

Yes 4)

1) Use on a rearward-facing vehicle seat (e.g. in a van or minibus) is only permitted if the vehicle

seat is also approved for use by adults. The seat may not be in the area of eect of an airbag.

2) The safety belt must be approved to ECE R 16 or a comparable standard, e.g. see whether

there is an "E" or "e" in a circle on the belt test label.

3) If there is a front airbag: Slide the vehicle seat a long way back and refer to any instructions

in the vehicle owner's manual.

4) Cannot be used if the vehicle seat is equipped with only a 2-point belt.

PAGE I

7. HARNESS BUCKLE CARE

1. PRODUCT OVERVIEW

DISPOSAL:

Please observe the waste disposal regulations in your country.

Disposal of packaging Container for cardboard boxes

Seat cover Residual waste, waste incineration

Plastic parts To be placed in the corresponding

container according to labelling

Metal parts Container for metals

Belt straps Container for polyester

Buckle and tongue Residual waste

6. CARE AND MAINTENANCE

Please ensure that you only use original BRITAX RÖMER replacement

covers, as the seat cover is an integral part of the child safety seat and fulls

important functions to ensure the smooth operation of the system. Replace-

ment covers are available from your dealer.

• The cover can be removed and washed in accordance with the instruc-

tions on the wash care label.

• The plastic parts can be cleaned using soapy water. Do not use any caus-

tic cleaning agents (such as solvents).

DANGER! The child seat must not be used without the seat cover.

CAUTION! Never remove the buckle tongues 30 from the straps.

9 to 36 kg

(~9 months to

12 years of age)

www.britax.com

2000025513 16/08

EVOLVA 1-2-3 SL SICT

User instructions

5. CHANGING THE HARNESS

Removing the 5-point harness

1. Loosen the harness straps as far as possible (see 9.1).

2. Push the shoulder strap adjuster 24 all the way up

(see 8.1).

3. Unhook the shoulder straps 13 from the connecting

piece 14 .

4. Clip the connecting piece 14 at the bottom of the

backrest 04 into its holder 11 .

5. Push down the strap loops of the shoulder pads 18

from the base of the shoulder strap adjuster 24 .

6. Pull the shoulder straps 13 and the strap loops of the

shoulder pads 18 out of the belt slots.

7. Undo the Velcro fastener on the crotch cushion 21 and

remove it.

8. On the bottom of the seat, unhook the adjusting strap

23 from the metal plate 27 .

9. Turn the metal plate 27 (that holds the harness buckle

19 to the seat shell) on end and push it upwards

through the belt slot 28 .

10. Release the harness buckle 19 .

11. Push the straps and buckle tongues 30 through the lap

belt slots in the cover.

12. Place the harness buckle 19 under the cover and inside

the storage compartment 31 of the backrest 04 .

13. Push the adjusting strap 23 under the cover.

14. Fix the shoulder pads 18 and shoulder straps 13 in the

rubber loops 32 at the feed-through points 15 .

Installing the 5-point harness

► To install the straps, follow the steps in reverse order.

DANGER! Tug on the shoulder straps ﬁrmly 13 to make

sure that the 5-point harness is secure.

Removing the cover

1. Adjust the headrest by moving it up 16 (see 9.1).

2. Unhook the edge of the cover and the rubber loops on

the back of the headrest 16 .

3. Pull o the cover of the headrest 16 .

4. Unhook the rubber loops from the retaining screws on

the backrest 04 .

5. Loosen the shoulder straps 13 (see 9.2).

6. Undo the Velcro fastener on the crotch cushion

21 and

remove it.

7. Open the snaps

on the left and right-hand sides of the

backrest cover

04 .

8. Unthread the harness buckle

19 and the adjusting strap

23 from the cover.

9. On the bottom of the seat, unhook the rubber loop of

the cover from the retaining screws and cover ﬂaps 24 .

10. Working from the side, carefully pull the edge of the

cover on the backrest 04 over the SICT 08 .

11. Slide the cover with opening over the headrest 16 .

►The cover can now be washed in accordance with the

instructions on the wash care label.

Re-ﬁtting the cover

►Proceed in reverse order to re-ﬁt the cover.

WARNING! Ensure that the straps are not twisted and

that they have been correctly inserted in the belt slots on

the cover.

To ensure the safety of your child, it is absolutely essential that the harness

buckle continues to function correctly. Harness buckle malfunctions are usually

caused by a build-up of soiling or by external objects.

Possible faults:

• When you press the red release button, it takes a long time for the buckle

tongues to be ejected.

• The buckle tongues no longer engage (i.e. when you try to push them in, they

pop out again).

• The buckle tongues engage without an audible "click".

• The buckle tongues are dicult to push in (you feel a certain amount of

resistance).

►Remedy: Clean the harness buckle so that it functions properly again:

Cleaning the harness buckle

1. Remove the harness buckle 19 (see 5.1).

2. Soak the buckle 19 in warm water containing washing-up

liquid for at least an hour.

3. Rinse the buckle 19 thoroughly and dry it.

4. Turn the metal plate 27 on end and push it downwards

through the belt slot 28 in the cover and through the

seat shell.

5. Turn the metal plate 27 90° and hook the adjusting strap

23 into the metal plate 27 (5.8).

DANGER! Tug hard on the harness buckle 19 to make

sure that it is secure.

6. Push the crotch cushion 21 into the belt slot and use the

Velcro fastener to ﬁx it to the harness buckle.

01 02

01 ISOFIX fastening points (car) 06 ISOFIT Locking button

02 ISOFIX insertion aids 07 ISOFIT locking arms

03 Headrest adjuster 08 SICT

04 Backrest 09 Cover ﬂap

Compartment for the user instructions

10 ISOFIT adjustment button

If you have any questions regarding the use of the product, please feel free to contact us:

2. APPROVAL

BRITAX RÖMER

Vehicle child

safety seat

Tested and approved according to ECE* R 44/04

*ECE = European Standard for Child Safety Equipment

Group Body weight

EVOLVA 1-2-3 SL

SICT

I 9 to 18 kg

II+III 15 to 36 kg

The child safety seat has been designed, tested and approved according

to the requirements of the European Standard for Child Safety Equipment

(ECER44/04). The seal of approval E (in a circle) and the approval number are

located on the orange approval label (sticker on the child safety seat).

DANGER! This approval will be invalidated if you make any modiﬁcations to

the child safety seat. Only the manufacturer is permitted to make modiﬁca-

tions to the child safety seat.

WARNING! Use the EVOLVA 1-2-3 SL SICT exclusively for securing your

child in your vehicle. It is in no way suitable for use as a seat or toy in the

home.

DANGER! Never secure your child or the child safety seat with a 2-point

belt. If you secure your child in the child seat with only a 2-point belt, this

may cause serious injuries to your child in the event of an accident and could

even result in their death.

DANGER! Never use installation method A for the child safety seat unless

the harness buckle and shoulder pads are properly attached (the straight

edges of the shoulder pads must be pointing towards each other). Make

sure that the metal plate of the harness buckle is correctly attached.

WARNING! Ensure that the straps are not twisted, that they have not been

accidentally interchanged and that they have been correctly inserted in the

belt slots on the cover.

23 27

1813

13 14

160908_EVOLVA_123_SICT_DRAFT_GB_GRAFIKEN.indd 1 9/7/2016 9:04:53 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Britax-Romer EVOLVA 1-2-3 SL SICT in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Britax-Romer EVOLVA 1-2-3 SL SICT

Britax-Romer EVOLVA 1-2-3 SL SICT User Manual - German - 2 pages

Britax-Romer EVOLVA 1-2-3 SL SICT User Manual - Dutch - 2 pages

Britax-Romer EVOLVA 1-2-3 SL SICT User Manual - French - 2 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Britax-Romer EVOLVA 1-2-3 SL SICT Manual

Product: