569540
7
Zoom out
Zoom in
Previous page
1/16
Next page
To turn on the TimeLapse Camera
To turn o the TimeLapse Camera
• If the USB flash drive is full, or the batteries are completely empty, TimeLapse Camera will not turn on. If the
batteries are too low for normal operation, it will turn on and beep twice, the red LED will turn on, and then
TimeLapse Camera will beep six times and turn off. If the USB flash drive is full, or not installed, TimeLapse
Cam will turn on and beep twice, then after a few seconds the blue LED will turn on, then TimeLapse Camera
will beep six times and turn off.
• When TimeLapse Camera is in operation the green LED will turn on for about one second every 15 seconds to
indicate that the camera is running properly and is ready to take photos.
• If there is any other status to report, the camera will do so at the same time as the green LED flashes. If the
batteries are getting low the red LED will turn on in unison with the green LED. If the USB flash drive is getting
close to being full, then the blue LED will turn on in unison with the green LED.
• If the camera has previously automatically shut down due to low batteries or a full USB flash drive, the next
time the power button is pressed the red or blue LED will turn on and will stay on until the green LED turns on.
This allows you to determine the cause of the automatic shutdown so that the appropriate corrective action
can be taken.
• The green LED will also turn on and flicker for a few seconds while a picture is captured at the chosen time
setting, and then is stored on the USB flash drive. This indication of TimeLapse Camera activity is independent
of the status indication that occurs every 15 seconds.
NOTE
On the front of the TimeLapse Camera, above the lens, there are three LED lights.
These LEDs allow you to monitor the status of the camera without having to move the camera from its
mounted position.
Press and hold the orange power button on the front of the camera until the green LED lights up. After a few
seconds the TimeLapse Camera will beep twice to indicate it has properly initialized and is waiting to start
a time-lapse sequence. After a delay of approximately 5 seconds the TimeLapse Camera will take the rst
picture of the time-lapse sequence.
Press and hold the orange power button until the TimeLapse Camera beeps three times and the green
LED turns o. This may take several seconds because the TimeLapse Camera must rst power itself on
and initialize before it recognizes the turn o request. Please be patient and wait for the beeps and LED
indication.
Each LED supports a dierent function:
Green LED light: Power ON/OFF and status
Red LED light: Low battery level
Blue LED light: Low USB ash drive level
Beep:
Power ON: Two beeps
Power OFF: Three beeps
Register setting change: Three beeps
Error status: Six beeps
(error = no USB ash driver, USB memory short, low battery)
TimeLapse Camera Operation
5 -
Brinno TimeLapse Camera
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brinno TLC 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brinno TLC 100 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info