535556
1
Zoom out
Zoom in
Previous page
1/2
Next page
-1-
WAARSCHUWING!
Schakel de hoofdschakelaar naar het apparaat uit voordat be-
gonnen wordt met service of onderhoud. Elektrische schok kan
leiden tot persoonlijk letsel. Lees en volg nauwgezet de instal-
latieinstructies; onjuiste aansluiting van de bedrading kan blij-
vende schade aan het product veroorzaken.
WARNING!
Before performing service or maintenance operations on the
systems, turn OFF main power switches to the unit. Electric
shock can cause personal injury. Please read and follow the
wiring instructions precisely; miswiring may cause permanent
damage to the product.
Basis installatie volgorde CO
2
- sensor
- Neem het voor en achterdeel los van elkaar.
- Bevestig het achterste gedeelte (grondplaat) aan de muur of
aansluitdoos met behulp van de meegeleverde schroeven;
sluit de benodigde bedrading aan.
- Plaats de CO
2
-sensor op grondplaat; monteer de sensor
eerst aan de bovenste klemmmen en klik daarna de sensor
vast aan de onderste klemmen. Zet de CO
2
-sensor vast met
de meegeleverde schroef.
Basic installation CO
2
- sensor
- Separate the case into its front and rear sections.
- Secure the rear section of the case (base plate) to the wall
or junction box using the supplied screws, and make neces-
sary wire connections.
- Mount the CO
2
- sensor on the base by aligning the top clips
and then securing to the bottom clips. Secure the CO
2
-
sen-
sor with the supplied set screw.
Grondplaat CO
2
- sensor
Base plate CO
2
- sensor
Jumper instelling CO
2
- sensor
Op sticker grondplaat staat aangegeven hoe jumper aan bin-
nenzijde van de CO
2
- sensor moet worden geplaatst.
Wordt de CO
2
-
sensor aangesloten op een Brink toestel
zoals b.v. een Renovent Excellent of een Renovent Sky
dan moet de jumper altijd worden ingesteld op 0-10 V!
Label on baseplate shows how jumper inside of the CO
2
sensor
should be placed.
When the CO
2
- sensor is connected to a Brink device
such as Renovent Excellent or Renovent Sky, the jum-
per must always be set to 0-10 V!
Jumper settings CO
2
- sensor
Bedradingsschema CO
2
- sensor
9ROJGHVSHFL¿HNHLQVWUXFWLHVYRRUGHEHGUDGLQJ'HDDQEHYR-
len draaddikte is 18-22 AWG (0,75 tot 1,0 mm
2
).
3OHDVH IROORZ WKH VSHFL¿F LQVWUXFWLRQV IRU ZLULQJ7KHUHFRP-
mended wire gauge is 18-22 AWG (0.75 to 1.0 metric).
Wiring diagram CO
2
- sensor
7HFKQLVFKHVSHFL¿FDWLHVWHFKQLFDOVSHFL¿FDWLRQV
Meetmethode
1LHWGLVSHUVLHYHLQIUDURRG1',5
absorptie vergulde optica
Sensing method
1RQGLVSHUVLYHLQIUDUHG1',5
absorption gold-plated optics
Meetbereik
0 - 2000 ppm (0 ppm = 0 V, 4 mA;
SSP 9P$
0HDVXUHPHQW5DQJH
Nauwkeurigheid
400-1250 ppm - ±30 ppm or 3%
1250-5000 ppm - ±30 ppm or 5%
Accuracy
Voeding
9$&506+]
9'&SRODULW\SURWHFWHG
Power Supply
Stroomverbruik
0.7 W (nom. voltage 24V AC)
Power Consumption
Stabiliteit
<2% gedurende levensduur sensor
(15 jaar)
Stability
<2% over life of sensor (15 years)
&HUWL¿FHULQJ &RQIRUP&(HQ5R+6
&HUWL¿FDWLRQV &(DQG5R+6FRPSOLDQW
Signaal update Elke 5 seconden
Signal Update Every 5 seconds
Opwarmtijd
< 2 minutes (operational)
10 minutes (max. )
:DUPXS7LPH
Bedrijfsomstandigheden
0°C - 50°C
5+QRQFRQGHQVLQJ
Operating Conditions
Opslagcondities
-40°C - 70°C
Storage Conditions
%ULQNWRHVWHO%ULQNGHYLFH
5HQRYHQW([FHOOHQW
5HQRYHQW6N\
NL
GB
NL
GB
NL
GB
NL
GB
28 mm
82 mm
PP
;9ROW
X15 - 5 (24 Volt -)
X15 - 3 (Ground 0 - 10 Volt)
X15 - 4 (0 - 10 Volt )
Jumper positie
Position jumper
%ULQN&OLPDWH6\VWHPV%95'%JHOVWUDDW'$6WDSKRUVW32%R[1/$$6WDSKRUVW
7)LQIR#EULQNFOLPDWHV\VWHPVQOZZZEULQNFOLPDWHV\VWHPVQO
Installatiehandleiding CO
2
- sensor
Installationmanual CO
2
- sensor
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brink CO2- sensor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brink CO2- sensor in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info