ALARM TIME
1. In normal time mode, press [ TIME ] key to select the alarm 1 or alarm 2.
2. In alarm1/alarm2 mode, press and hold [ ALARM key for 2 seconds until alarm hour
digit ashes.
3. Press [ CH /
] or [ 12/24 / ] key to change the value
4. Repeat the above operations to set the alarm time in this order: Hour
Minute
Ice pre-alarm on/o.
5. Press [ key or leave the unit for 30 seconds to return to normal mode.
Ti
Ice alert icon
USING ALARM
1. Set the desired alarm time as described in the previous section.
2. Or press [ ALARM key to turn on alarm 1, press it again to turn on alarm 2, press
it thrice to turn on both alarm 1 and alarm 2, with the alarm icons “
” and / or “
” displays on the LCD. Press it again to turn o both alarm 1 and alarm 2, with the
icons disappear
3. When clock reach the alarm time, alarm sound will start.
Where it can be stopped by following operation:
a)
again in the next day
b) [ SNOOZE / LIGHT ] key to enter snooze that the alarm will sound again
after 5 minutes.
c) [ SNOOZE / LIGHT ] key for 2 seconds to stop the alarm and
will activate again in the next day
d) [ ALARM key to stop the alarm and the alarm will activate again in the
next day
NOTE:
The alarm function will turn on automatically once you set the alarm time.
The snooze could be used continuously in 24 hours.
During the snooze, the alarm icons “
” and / or “ ” will keep ashing.
The ice pre-alarm will be activated when the alarm 1 and / or 2 is on.
Once the ice pre-alarm activates, the preset alarm will sound 30 minutes earlier if the
outdoor temperature is below -3°C.
T
a.
b.
READING INDOOR/
In normal mode, press [ °C / °F ] key to switch between °C /°F temperature unit. The
temperature and humidity will display “Hi / Lo / --” on the conditions in the following chart:
Area Condition Display
T
T LO
T HI
Humidity
Humidity < 20% LO
Humidity > 90% HI
T --
NOTE:
If no signals are received or the transmission is interfered, “- -” will appear on the LCD.
Relocate the main unit or the transmitter in other positions and make sure the
transmission is within the eective range of 30m approx.
BARO,
The Barometric pressure, temperature and humidity trend indicator shows the trends of
changes in the forthcoming few minutes.
Arrow indicator
T Rising Steady Falling
BAROMETRIC/A
TO SELECT THE PRESSURE DISPLA
Press and hold the [ BARO ] key for 2 seconds to enter select model that allow you
select between:
abs --- the absolute atmospheric pressure of your location.
rel --- the relative atmospheric pressure based on the sea.
TO SET RELA
1. Get the atmosphere pressure data of the sea level (it is also the relative atmosphere
pressure data of your home area) through the local weather service, internet and
other weather channels.
2. Press and hold [ BARO ] key for 2 seconds until “abs” or “rel” icon ashes.
3. Press [ CH /
] or [ 12/24 / ] key to switch to “rel” mode.
4. Press [ BARO ] key once again until the “rel” atmosphere pressure digit ashes.
5. Press [ CH /
] or [ 12/24 / ] key to change its value.
6. Press [ BARO ] key to save and exit the setting mode, or let it exit automatically 30
seconds later without pressing any key
TO SELECT THE MEASUREMENT UNIT FOR THE BAROMETER
Use the [ BARO ] key to change the unit between hPa (mb) / inHg.
NOTE:
When power up the main unit, it will display the relative pressure reading and default
value is 1013 mb/hPa (29.91 inHg), which refers to the average atmosphere pressure.
When you change the relative atmosphere pressure value, the weather indicators will
change along with it.
The relative atmosphere pressure is based on the sea level, but it will change with the
absolute atmosphere pressure changes after operating the clock for 1 hour
WEA
The built-in barometer can notice atmosphere pressure changes. Based on the data
collected, it can predict the weather conditions in the forthcoming 24 hours.
Sunny Partly Cloudy Cloudy Rainy Stormy Snowy
NOTE:
1. The accuracy of a general pressure-based weather forecast is about 70% to 75%.
2. The weather forecast is meant for the next 24 hours, it may not necessarily reect the
current situation.
3. The Snowy weather forecast is not based on the atmospheric pressure, but based
on the temperature of current channel. When the outdoor temperature is below -3°C,
the Snowy weather indicator will be displayed on the 24 HOUR FORECAST display
section.
P
The current and historical atmosphere is shown near the
24 HOUR FORECAST section.
T
past 24 hours, press the [ HISTOR key
the key will go back by an hour
Under the pressure history mode, press any key (except
[HISTOR key) to go back the normal mode, or let it exit
automatically 30 seconds later without pressing any key
HISTOR
The history graph is under the time section of the LCD
displays that can show the Baro histories in bar chart
format.
MAX /
The main unit preserves the MAX / MIN weather data records since the last manual
reset.
1. In normal mode, press [ MEM ] key once to show the indoor & current outdoor
channel maximum temperature and humidity records.
2. Press [ MEM ] key repeatedly to show the minimum records.
3. Press [ MEM ] key again to exit.
4. T[ MEM ] key for 3 seconds.
MOON PHASE
The main unit can show the northern hemisphere moon phase status, below is the table
which illustrate how the moon will appear on the main unit.
Moon Phase Icon
Description
Moon Phase Icon
Description
New Moon Full Moon
W W
First quarter Third quarter
W W
LOW BA
When the battery indicator “
” appear on the clock section or the LCD becomes
dim, replace with 2 new
”
appear in the outdoor section, it indicates that the battery power of the transmitter is not
enough, and you should replace with 2 x
IMPORT
This main unit is intended to be used only indoors.
Do not subject the unit to excessive force, shock, dust, temperature or humidity
Do not cover the ventilation holes with any items such as newspapers, curtains etc.
Do not immerse the unit in water
soft, lint-free cloth.
Do not clean the unit with abrasive or corrosive materials.
Do not tamper with the unit’s internal components. This invalidates the warranty
Only use fresh batteries. Do not mix new and old batteries.
Do not dispose old batteries as unsorted municipal waste. Collection of such waste
separately for special treatment is necessary
Attention! Please dispose of used unit or batteries in an ecologically safe
manner
T
subject to change without notice.
SPECIFICA
MAIN UNIT
Dimensions (W x H x D) 140 x 103.5 x 51mm
Main power 2 x
Barometer display range 540 to 1
Operating temperature range -5°C to 50°C ( 23°F to 122°F )
Display temperature range (In / Outdoor) -40°C to 70°C (-40°F to 158°F)
Display humidity range (In / Outdoor) RH 20% to 90 %
Resolution of temperature
1 decimal place of °C/°F (above -10°C / °F)
Integer of °C/°F (below -10°C / °F or above
100 °F)
Resolution of humidity 1%
Number of sensors support Up to 3 units
Radio controlled signal DCF 77 / MSF (depend on country version)
WIRELESS SENSOR
Dimensions (W x H x D) 65 x 100 x 35mm
Main power
2 x
(Lithium battery recommended for low
temperature environment)
Operating temperature range -20°C to 60°C ( -4°F to 140°F )
Operating humidity range RH 1% to 99 % (non-condensing)
RF frequency 433MHz
RF transmission range 30 meters
Errors and technical changes reserved. / Manual_7006405_T
Bresser GmbH Gutenbergstr
