Manual Bremshey Orbit Pacer (page 6 of 60) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

648512

Zoom out

Zoom in

1/60

O W N E R ' S M A N U A L

•

PA C E R

Start training by pressing START/STOP button.

If you have set target/targets, the target/targets start

to count down. Adjust resistance with SELECTION

DIAL.

2. pRESET pROGRAMS

Preset program profile is shown for two seconds

while programs are browsed. Select desired preset

program by using the SELECTION DIAL.

Set time for training and/or target distance and/or

energy and/or upper heart rate limit by SELECTION

DIAL.

Start training by pressing START/STOP button.

If you have set target/targets, the target/targets

start to count down. During training you can scale

the load by SELECTION DIAL.

3. USER pROGRAM

The program profile used last time is displayed.

You can either start training with your personal

memorized training targets by pressing START/

STOP or modify the program. The program profile

bar (1/20) that can now be modified blinks. If

you want to change, modify the blinking bar and

confirm. Next bar will blink. After the last bar, the

display switches back to the first bar. By pressing

the ENTER button for 2 seconds you can finish the

profile modifying. Now program is ready with your

memorized personal training data (time, distance,

energy targets and heart rate limit). Modify your

targets if needed. Start training by pressing START/

STOP button.

If you have set target/targets, the target/targets

start to count down. During training you can scale

the load by SELECTION DIAL

4. HEART RATE CONTROL (H.R.C.)

Select your age and confirm. Select between four

different training intensities (55%, 75%, 90% or

TARGET.) By selecting TARGET you can insert target

heart rate.

Start training by pressing START/STOP button. If you

have set target/targets, the target/targets start to

count down.

During the training the equipment will

automatically adjust the resistance so that your

heart rate target will be reached and maintained.

5. CONSTANT WATT

Set target power in watts and target time and/or

distance and/or energy consumption and/or upper

heart rate limit by SELECTION DIAL.

Start training by pressing START/STOP button.

If you have set target/targets, the target/targets

start to count down. During training the equipment

will adjust resistance dependently on your pedaling

speed, so that target power level is achieved and

maintained. You can change the target power by

SELECTION DIAL.

6. RECOVERY

Start the recovery calculation after training by

pressing RECOVERY button. Recovey heart rate

calculation can be started only if the heart rate

measurement is activated and the heart rate value

is shown on the display The measurement takes 60

seconds. After 60 seconds, the display shows your

recovery index F1-F6 (F1 = best result). To get back

to main menu, press RECOVERY button once again.

SETTING USER DATA

Right after restarting the meter you can choose the

user. Select the user and confirm. Personal exercise

data (time, distance, energy, heart rate limit and age)

will be memorized and recalled as defaults every

time when the user is selected.

ADDITIONAL NOTES

1. For speed and distance you can choose either

metric or English units by using the KM/ML switch

located on the back cover of the meter. The power

cord has to be unplugged and replugged to apply

the change.

2. If you are not training and buttons are not

pressed, the meter switches into the Sleep mode

after about four minutes. Room temperature is

displayed.

3. Training is paused for a maximum of 4 minutes

by pressing the START/STOP button. Pressing the

button again allows you to continue the paused

training session using the previous training data.

4. Entering training targets (time, distance, energy,

heart rate limit) is possible only in the STOP mode

(not during training).

5. This equipment cannot be used for therapeutic

purposes.

6. Energy consumption is calculated based on

average values. The energy expenditure is displayed

in kilocalories. To convert this into joules, use the

formula: 1 Kcal = 4.187 KJ.

7. If you are training with heart rate measurement

(either chest belt or handgrip heart rate) you can set

maximum heart rate limit. When limit is exceeded

while training meter will give alarm beeps.

8. Preset programs are divided into 20 steps.

Duration of the one step depends on the time set

for the whole training. If time is not set, duration of

one step will be 100 m in distance.

9. If you have set targets to count down, a signal

sounds and training automatically stops when any

of target reaches zero. You can restart training by

pressing START/STOP.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bremshey Orbit Pacer in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 3,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bremshey Orbit Pacer Manual

Product: