779007
5
Zoom out
Zoom in
Previous page
1/17
Next page
EN
9
5. Attach a trouser clip or brush onto the nozzle as
required. Place the nozzle on the hanger.
6. Remove water container from the device. Unscrew it,
ll with water, screw it closed and insert back into the
device.
7. Select the operating mode and switch the device
on. In models BCGS-1E, BCGS-1RE use knob (5) to
select the operating mode, in model BCGS-1RP use
a combination of the On/O switches (mode 1 – use
left switch mode 2 – use right switch, mode 3 – use
both switches at the same time).
BCGS-2RP model
1. Press the lock button and insert the metal telescopic
pipe in the hole.
2. Attach hanger to the upper part of the telescopic
stand.
3. Set the stand to the required height as shown on the
diagram below: release the catch, set the height and
secure the catch.
Released: Secured:
4. Attach the steam hose by inserting into the correct
opening in the device. Twist the hose to secure it.
5. Attach a trouser clip or brush onto the nozzle as
required. Place the nozzle on the hanger.
6. Remove water container from the device. Unscrew it,
ll with water, screw it closed and insert back into the
device.
7. Select the operating mode and switch the device
on. Use knob (5) to select the operating mode. The
steam station will be ready for use after approx. 45
seconds. Hang the fabric to be ironed on the hanger.
Start ironing.
USE GUIDELINES:
Use of distilled or demineralised water is
recommended. Tap water may result in limescale
deposits in the device, leading to a decrease in
eciency or failure of the steam station.
Do not add detergents, fragrances etc. to the water
in the container. This may damage the device.
Avoid bending the steam hose.
Before starting ironing, straighten the garment on
the hanger as best as possible.
Depending on the type of garment to be ironed, use
vertical or horizontal movements. Observe garment
manufacturer‘s guidelines.
Do not use the device for ironing garments in
a horizontal position, always hold the nozzle
pointing upwards – condensed steam can return
to the water container and water dripping from the
nozzle is reduced.
Thick fabrics require more ironing time.
Pay special attention when ironing fabrics decorated
with gemstones, sequins, etc, hot steam may
damage them.
Do not use hands to support / hold garments while
ironing. Risk of burns.
When not in use, during transport or when lling /
emptying the water container, make sure the device
is switched o.
To move the device roll it along on its wheels by
pushing the telescopic handle.
To empty the water container, wait 20 minutes after
end of use for the device to cool down.
Monitor the water level in the container. If the water
container is empty do not switch the device on.
TRANSPORTATION AND STORAGE
Shaking, crashing and turning upside down of the device
should be prevented when transporting it. Store it in
a properly ventilated location with dry air and without any
corrosive gas.
CLEANING AND MAINTENANCE
Always unplug the device before cleaning it.
Use a damp, wet cloth to clean device surfaces.
Do not use detergents with corrosive, abrasive etc.
substances.
After each use empty the water container.
REGULAR CONTROL OF THE DEVICE
Check regularly if the device is damaged. In case of
damage, please stop using it immediately and contact
customer service for solving the problem
What to do in case of a problem?
Please contact customer service and prepare the following
information:
Invoice number and serial number (the latter is to be
found on the technical plate on the device).
If necessary, take a picture of the damaged, broken
or defective part.
It will be easier for your customer service assistant
to determine the source of the problem if you give
a detailed and precise description of the problem.
The more detailed your information, the better
customer service will be able to solve your problem
rapidly and eciently!
CAUTION: Never open the device without the authorization
of your customer service. This can lead to a loss of warranty!
8
EN
1. Hanger
2. Steam hose
3. Telescopic stand
4. Water container
5. Operating mode selector knob
6. Nozzle
WARNING: Instead of an operating mode selector knob
(5) the BCGS-1RP model features a double On/O switch.
List of accessories:
Hanger
BERORE THE FIRST USE
Upon receipt of the goods, check the packaging for
integrity and open it. If the packaging is damaged, please
contact your transport company and distributor within 3
days, and document the damages as detailed as possible.
Do not turn the package upside down! When transporting
the package, please ensure that it is kept horizontal and
stable.
DISPOSING OF PACKAGING
Please keep all packaging materials (cardboard, plastic
tapes and Styrofoam), so that in case of a problem, the
device can be sent back to the service centre in accurate
condition!
INSTALLING THE APPLIANCE
APPLIANCE LOCATION
The work surface where the device will be located must
be suitable for the size of the appliance, please refer to
the measurements. The work surface must be levelled,
dry, heat-resistant and at a tting height from the ground
to enable a proper use of the device. The power cord
connected with the appliance must be properly grounded
and correspond to the technical details.
DEVICE OPERATION – BASIC PRINCIPLES
Models BCGS-1E, BCGS-1RE,
BCGS-1RP Model BCGS-2RP
1
6
2
3
4
554
3
2
1
6
or
clip for
trousers
brush
OPERATION
Preparing for use
BCGS-1E, BCGS-1RE, BCGS-1RP models
1. Place the metal telescopic pipe in the device and
twist in order to secure as shown on the diagram
below:
2. Attach hanger to the upper part of the telescopic
stand.
3. Set the stand to the required height as shown on the
diagram below: release the catch, set the height and
secure the catch.
4. Attach the steam hose by inserting into the correct
opening in the device. Twist the hose to secure it.
The steam station will be ready for use after approx.
45 seconds. Hang the fabric to be ironed on the
hanger. Start ironing.
21.12.2017
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bredeco BCGS-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bredeco BCGS-1 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info