487440
5
Zoom out
Zoom in
Previous page
1/28
Next page
Assembling the chimney
Hood to be used with external evacuation : fig. 4 and 9
- Push the non-return valves (fig. 6).
- Remove the two attachment clips provided for the transportation of the chimneys.
- Remove the two attachment screws from the plastic deflector (in recycle mode only).
- Attach the metal chimney bracket to the wall, also placing this against the ceiling (fig. 7).
Take care in aligning the 2 triangular slots on the metal bracket with the vertical line on the wall.
- In the case of a flue with a diameter of 125 mm, use the adapter supplied (fig. 9).
If your exterior duct is below 125 mm, you must obligatorily connect your hood in
recycling mode
- Prepare your telescopic chimney taking care to block off the vents (fig. 9).
Fit the chimneys into one another as far as they will go.
- Fit the upper part to the metal bracket.
- Adjust the length of the telescopic chimney by bringing down the lower part and fitting it to the
top of the hood.
Hood to be used in "recycling" mode : f
ig. 5 and 10
- It is possible to remove the back flow valves.
- Fit the plastic smoke deflector to the wall also placing this against the ceiling.
Take care to centre the deflector vis-à-vis the vertical line drawn on the wall (fig. 8).
- Prepare your chimney taking care to place the vents toward the top to ensure that
they are visible (fig. 10).
- Fit the upper part to the plastic deflector.
- Adjust the length of the telescopic chimney by bringing down the lower part and fitting it into
the top of the hood.
To ensure optimal use of your device, we advise that you connect a flue with a
diameter of 150 mm (not supplied). Limit the number of angles and bends as
far as possible, and keep the length of the flue to a minimum. In the event
that the hood will be functioning using exterior evacuation, you should ensure
a sufficient inlet of fresh air to avoid a pressure deficiency in the room.
Model with G4-20W-12V halogen lamp:
(fig. 13)
1. Remove the viewing port.
2. Change the halogen lamp.
3. Replace the lamp assembly by carrying
out the above operations in reverse order.
Changing the lamp ?
Before carrying out any work, the power supply to the hood must be turned off,
either by unplugging it or by using the circuit breaker switch,
Model wi
th E14- 40 W type bulb:
(fig. 12)
1. Undo the screw of the shade.
2. Swing it away.
3. Change the bulb by unscrewing it then
screw in the new one.
4. Replace the shade.
5. Replace the screw.
GB
99626002_ML.qxd 01/07/03 12:42 Page 5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brandt adw229w at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brandt adw229w in the language / languages: English, Dutch, French, Portuguese as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info