487441
4
Zoom out
Zoom in
Previous page
1/44
Next page
The hood must be installed in conformity with the applicable regulations
concerning the ventilation of premises. In France, these regulations are
detailed in DTU 61.1 from the CSTB. In particular, the evacuated air must not
be channelled into a duct used to evacuate fumes from appliances using gas or
other combustible fuels. Disused ducts may only be used after approval from a
competent specialist.
The minimum distance between the cooking surface and the lowest part of the
hood must be 70 cm. If the instructions for the hob installed under the hood
specify a distance of more than 70 cm, this requirement must be respected.
Installing your hood ?
If you possess an outlet to the exterior: fig. 4
Your hood can be connected to this using a flue (minimum Ø 125 mm, enamelled, made from
aluminium, flexible or made from a non-flammable material). If your flue is below 125 mm in
diameter, you must obligatorily use the "recycling" mode.
If you do not possess an outlet to the exterior: fig. 5
All of our appliances can be used in recycling mode.
In this case, you should add an active carbon filter which will keep in odours.
- Place the assembly template against the wall: fig. 2
- Draw a vertical line on the wall in order to perfectly line up your hood with your
cooking appliance.
- Draw a mark on the vertical line at 70 cm (minimum) from your hob.
Note
: in the case of a hollow wall, you should use suitable screws and wall plugs.
- Dismantle the filter cartridges (fig. 3).
- Attach the hood via its rectangular slots. The size of the slots enable you to position
the hood, moving it slightly to the left or right as needed (fig. 3).
Assembling your hood
Connecting up your hood
This appliance is delivered with a H 05 VVF power cable with three
conductors of 0.75 mm2 (neutral, live and earth). This must be
connected to the 220-240 V single phase mains network via a CEI 60083
standard plug which must remain accessible following installation, or an all
pole cut-off device with a minimum contact opening distance of 3 mm. We will
not be liable in the event of an accident arising following incorrect or
non-existent earthing. The fuse for your installation must be 10 or 16A. If the
power cable is damaged, call the after sales service department in order to
avoid danger.
Adjust the height and level by manoeuvring the bracket adjustment
screws ("A") and then attach the hood securely to the wall by tightening
the screws ("B") (Fig. 3).
99624583_ML_A.qxd 26/02/04 16:05 Page 4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brandt AD429B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brandt AD429B in the language / languages: English, German, Dutch, French, Italian, Portuguese as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info