706402

Bowers Wilkins MT-60D - M1 Manual

4
Zoom out
Zoom in
Previous page
1/6
Next page
ENGLISH
3 Moving the ball socket position
You can skip all of Section 3 completely if you are
going to use the speaker in portrait orientation on its
table stand as supplied, or you want to mount it high
on the wall with maximum downward tilt (Figure 7).
Note: To achieve maximum tilt, it is necessary to
invert the mounting of the wall bracket. (far right)
WARNING! This method ofxing is
potentially less secure, because gravity
will allow the product to fall if the stem
is not properly tted to the bracket. It is essential
that the tapered ridge of the clamp bar engages
the groove of the stem as shown in Section 5.
You are advised to avoid this method ofxing
unless the degree of tilt is absolutely necessary.
B&W Group cannot accept responsibility for any
damage or injury arising as a result of using this
method.
However, if you want to use it in landscape
orientation – perhaps for centre channel use – or
mount it on the wall in portrait orientation with the
bracket hidden behind the speaker (Figure 8), you
will need to change the position of the ball socket
from the bottom to the centre of the speaker.
3.1 Removing the table stand base
Peel off the rubber mat from the underside of the
base and remove the Torx key.
Locate the key in the cam-lock device and turn it
anti-clockwise to unlock the stem (Figure 9).
Part the base from the speaker (Figure 10).
3.2 Removing and turning the back cover
Remove the three screws as shown in Figure 11 and
pull the cover away from the back of the speaker.
Rotate the cover through 180º and re-assemble it
to the back of the speaker, now with the ball joint
positioned at the centre (Figure 12). Take care not to
trap any wires.
3.3 Rotating the stem
In all cases, loosen the accessible ball joint securing
screw (A), rotate the stem through 90º and tighten
the screw again. For landscape orientation, leave the
stem in that position (Figure 13).
For wall-mount portrait orientation, where you do
not need maximum downward tilt and want to hide
the wall bracket as much as possible behind the
speaker, loosen the other ball joint securing screw
(B), rotate the stem a further 90º and tighten the
screw (Figure 14).
Use the supplied Torx key.
4
Figure 8
Figure 7
Figure 9 Figure 10
Figure 11 Figure 12
A
Figure 13 Figure 14
27° max 40° max
B
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bowers Wilkins MT-60D - M1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bowers Wilkins MT-60D - M1 in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info