550926
8
Zoom out
Zoom in
Previous page
1/8
Next page
a
:÷
ä
B
@
@
B
B
:
~
a
a
a
11
What to do if ...
ʑ
Water is leaking out. Attach/replace the drainage hose correctly.
Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
Start not selected?
Tap not turned on?
Filter blocked? Clean the filter a page 10.
Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
Safety function active. Wait approx. 2 minutes.
ʑ
Programme does not
start.
Start selected?
Washing machine door closed?
ʑ
Detergent solution is not
drained.
Clean the detergent solution pump a page 10.
Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
Not a fault - water below the visible area.
ʑ
Unsatisfactory spin
result.
Laundry wet/too damp.
Not a fault - the unbalanced-load detection system has cancelled
the spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the
drum.
ʑ
Spin cycle performed
several times.
Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
Not a fault - the action of the care product is not affected.
Clean the insert if necessary a page 9.
ʑ
Odour formation in the
washing machine.
Run programme Cottons 90 °C without laundry. Use standard
detergent.
ʑ
Foam escaping from the
detergent drawer.
Too much detergent used?
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour
into compartment II (not with outdoor or down fabrics).
Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and “walking”
during the spin cycle.
Are the appliance feet fixed?
Secure the appliance feet a Installation instructions.
Transportation safety devices removed?
Remove the transportation safety devices a Installation
instructions.
ʑ
Noises during spin and
drain cycles.
Clean detergent-solution pump a page 10.
ʑ
The indicator lights do
not function during
operation.
Power cut?
Fuses tripped? Reset/change the fuse.
If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence
longer than usual.
Not a fault - unbalanced load detection system adjusts
imbalance by repeatedly distributing the laundry.
Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues on
the laundry.
Occasionally, phosphate-free detergents contain water-insoluble
residues.
Select Rinse or brush out the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
Turn the programme selector to Off and remove the mains plug from the socket.
Turn off the water supply and call the after-sales service a Installation instructions.
en operating instructions
Washing machine
WAE24063GB ...
8


Need help? Post your question in this forum.

Forumrules
1

Forum

bosch-wae24063---maxx-6

Reset search

  • After cycle completed the start and wash indicators flash and will not allow the door to release , this is after the load has been removed Submitted on 28-5-2024 at 15:55

    Reply Report abuse
  • Our machine won’t start Start and wash light up We have checked that the door is closed Submitted on 23-10-2022 at 21:50

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch WAE24063 - Maxx 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch WAE24063 - Maxx 6 in the language / languages: English as an attachment in your email.

The manual is 3,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info