551127
39
Zoom out
Zoom in
Previous page
1/42
Next page
Installation and connection en
39
Drinking water connection
1. Fasten the drinking water connection
to the tap according
to the installation instructions using
the enclosed parts.
Ensure that the drinking water
connection is not kinked, crushed
or twisted.
2. When replacing the appliance,
always use a new water supply hose.
Water pressure:
At least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing
valve ahead.
Inlet rate:
Minimum 10 litres/minute
Water temperature:
Cold water; hot water max. temperature
60 °C.
Warm water connection *
Warm water connection
* depending on model
The dishwasher can be connected
to cold or hot water up to max. 60 °C.
Connection to hot water
is recommended if the hot water can be
supplied by energetically favourable
means and from a suitable installation,
e.g. solar heating system with circulation
line.
This will save energy and time.
The hot water setting :‹‚ allows you
to adjust your appliance optimally
to operation with hot water.
It is recommended to have a water
temperature (temperature of the
incoming water) of at least 40 °C
and no more than 60 °C.
It is not recommended to connect
the appliance to hot water if the water
is supplied from an electric boiler.
Setting hot water:
1. Open the door.
2. Switch on ON/OFF switch (.
3. Hold down programme button #
and press START button `
until :... is indicated on the digital
display.
4. Release both buttons.
The LED for button # flashes and
the digital display h displays the
factory setting :‹….
5. Press programme button # until
the factory set value :‹‹
is indicated on the digital
display h.
To change the setting:
1. By pressing the 3 button, you can
switch the hot water setting off :‹‹
or on :‹‚.
2. Press START button `.
The set value is saved.
3. Close the door.
Electrical connection
Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See
rating plate for required fusing 9:.
The socket must be near
the appliance and freely accessible
following installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side
to satisfy the relevant safety
instructions.
The connection may be modified by
technicians only.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch SMV65N00EU - SuperSilence at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch SMV65N00EU - SuperSilence in the language / languages: English as an attachment in your email.

The manual is 2,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch SMV65N00EU - SuperSilence

Bosch SMV65N00EU - SuperSilence User Manual - German - 44 pages

Bosch SMV65N00EU - SuperSilence User Manual - Dutch - 46 pages

Bosch SMV65N00EU - SuperSilence User Manual - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info