390388
11
Zoom out
Zoom in
Previous page
1/13
Next page
English - 7
Clamp the workpiece if it does not remain
stationary due to its own weight.
Do not strain the machine so heavily that it
comes to a standstill.
Grinding and cutting discs become very
hot while working; do not touch until they
have cooled.
Rough Grinding
The best roughing results are
achieved when setting the machine
at an angle of 30° to 40°. Move the
machine back and forth with mod-
erate pressure. In this manner, the
workpiece will not become too hot,
does not discolour and no grooves
are formed.
Never use a cutting disc for roughing.
Flap Disc
With the flap disc (accessory), curved surfaces
and profiles (contour sanding) can be worked.
Flap discs have a considerably higher service life
than sanding sheets, lower noise level and lower
sanding temperatures.
Cutting
When cutting, do not press, jam or
oscillate the machine. Work with
moderate feed, adapted to the ma-
terial being machined.
Do not reduce the speed of running
down cutting discs by applying
sideward pressure.
The direction in which
the cutting is per-
formed is important.
The machine must
always work in an
up-grinding motion.
Therefore, never
move the machine in
the other direction!
Otherwise, the dan-
ger exists of it being
pushed uncon-
trolled out of the cut.
Grinder Stand
With the grinder stand 26 (accessory), work-
pieces can be cut at angles of 0 to 45° at the
same lengths.
The safety notes and operating instructions in the
respective operating instructions manual of the
angle grinder are to be strictly observed. Use only
original Bosch grinder stands.
Cutting Stone
The machine must be used only for dry
cutting/grinding.
It is best to use a dia-
mond cutting disc. As
a safety measure
against jamming, use
the cutting guide 25
with the special dust
extraction protection
guard.
Operate the machine with dust extraction only. In
addition, wear a dust mask.
The vacuum cleaner
must be approved for
the extraction of ma-
sonry dust.
Bosch provides suita-
ble vacuum cleaners.
Switch on the ma-
chine and place the
front part of the cut-
ting guide on the
workpiece.
Slide the machine with moderate feed, adapted
to the material to be worked (Figure).
Operating Instructions
26
1 609 929 F75.book Seite 7 Dienstag, 9. März 2004 9:19 09
12 • 1 609 929 F75 • 04.03
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch gws 20 180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch gws 20 180 in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch gws 20 180

Bosch gws 20 180 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 122 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info