647502

Boretti BIK-97 Manual

56
Zoom out
Zoom in
Previous page
1/60
Next page
56
Electrical connection
• The installation of this appliance and the connection to the electrical network should be entrus-
ted only to an electrician perfectly to the fact of the normative regulations and which respects
them scrupulously.
• Protection against the parts under tension must be ensured after the builting-in.
• The data of connection necessary are on the stickers place on the hob casing near the con-
nection box.
• The connection to the main must be made using an earthed plug or via an omnipolar circuit
breaking device with a contact opening of at least 3 mm.
• The electrical circuit must be separated from the network by adapted devices, for example :
circuit breakers, fuses or contactors.
Caution !
This appliance has only to be connected to a network 230 V~ 50 Hz. Connect always the earth
wire. Respect the connection diagram. The connection box is located underneath at the back of
the hob casing. To open the cover use a medium screwdriver. Place it in the slits and open the
cover.
(*) calculated with the simultaneous factor following standard TN 60 335-2-6/1990.
Connecting the cooktop:
For the various connections use the brass bridges which are in the terminal box.
1 phase 23 0V~1F+N (not for the Netherlands!):
Place a bridge between 1 and 2 then between 4 and 5. Attach the earthing to the “earth” terminal
clamp, the neutral N to terminal clamp 4 or 5, and phase L to terminal clamp 1 or 2.
2 phases 400V~2F+N:
Place a bridge between 4 and 5. Attach the earthing to the “earth” terminal clamp, the neutral N
to terminal clamp 4 or 5, phase L1 to terminal clamp 1 and phase L2 to terminal clamp 2.
2 phases 23 0V~2F+2N:
Place a bridge between 2 and 3. Connect the earthing to the “earth” terminal clamp, neutral N1 to
terminal clamp 4, neutral N2 to terminal clamp 5, phase L1 to clamp 1 and phase L2 to clamp 2.
Caution ! ensure that you : correctly attach the wires and the bridges. Tighten the screws properly.
Before making the connection, we strongly advise you to locate the phase(s), neutral and earth on
the mains. If you have any doubts, call your electrician. Note: the bridges between terminals 4-5
and between terminals 1-2 were installed during the factory check. We cannot be held responsible
for any incident resulting from incorrect connection or which could arise from the use of an ap-
pliance which has not been earthed or has been equipped with a faulty earth connection.
Mains Connection Cable diameter Protection calibre
230V~1P+N 50Hz 1 Phase + N 3 x 2.5 mm² 25 A *
400V~2P+N 50Hz 2 Phases + N 4 x 1.5 mm² 16 A *
230V~2P+2N 50 Hz 2 Phases + 2N 5 x 1,5 mm² 16 A *
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Boretti BIK-97 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Boretti BIK-97 in the language / languages: English, Dutch, French, Spanish as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info