552085
6
Zoom out
Zoom in
Previous page
1/9
Next page
6
11/2012
R
EVERSE
T
HE
D
OOR
O
PENING
If required, the door opening can be moved from the right (supplied condition) to the left side.
WARNING
When replacing the door stop, the device must be disconnected
from the power supply. Always unplug the device first.
1. Use a small flat screwdriver to lift up the two screw covers
(1) on the top cover (3).
2. Use a cross screwdriver to remove the two screws (2) on the
top cover and the other two screws (11) on the backside of
top cover.
3. Lift up the top cover (3) and pull out the door hinge pin (4)
from the door, and put them on a safety place for later use.
Lift up the door (6) and put it on a safety place for later use.
4. Remove the left adjustable foot (7) and the right adjustable
foot (8) and screws (9) and keep them for later use.
5. Move the lower hinge (10) from the right side to the left side,
then fix it with the screws (9). Then install the right adjustable
foot (8) on the left and the left adjustable foot (7) on the right.
6. According to the reversible way of above procedure to install
the door (6), then put the door hinge pin (4) into the left hole of the door, then put the top cover (3)
on it, please make sure the door hinge pin (4) to be placed into the hole of the top cover (3), then
use the cross screw drive to fix the screws (2) and the screws (11), finally put the screw covers (1)
on it.
Check if the door is arranged vertical as well as horizontal, so that a smooth opening and closing of
door is ensured.
S
TARTUP
/
O
PERATION
Prior to First Use
ATTENTION: After transport, the device should be left standing for 4 hours in order for the oil to
be collected in the compressor.
Nonobservance could cause damage to the compressor and hence
result in failure of the device. This would void your warranty claim.
- Clean the interior of the device including all accessory parts located inside.
Connect the Device to the Mains Supply
IMPORTANT
- The device must be earthed properly. For this purpose the plug of the mains cable has been fitted
with the intended lead.
- Contact an electrician if the plug does not fit in the wall socket.
- In case you disconnect the device or in case of power failure: Wait for 5 minutes before restarting
the device.
Operation
Turn on the device by connecting the plug to a wall socket and turning the temperature control, which
is located at the right side of the fridge interior. Please also refer to chapter ‘Settings’.
Settings
Setting 0 – OFF indicates the device is turned off.
Turn the temperature control clockwise, starting from this setting; the device will turn on automatically.
The Settings 1 MIN 7 MAX regulate the inside temperature. When opening the door, the interior
lamp will turn on.
Setting 0 (or OFF) = Off
Setting 1 (or MIN) = lowest setting (warmest inside temperature)
Setting 7 (or MAX) = highest setting (coldest inside temperature)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bomann KS 263 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bomann KS 263 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bomann KS 263

Bomann KS 263 User Manual - German - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info