518710

BodyCraft Xpress Pro Legpress Manual

8
Zoom out
Zoom in
Previous page
1/10
Next page
STEP 3
LEG PRESS CABLE (243)
bolt end
metal ball end
-7-
1. Screw the threaded end (approximately half way) of the Leg Press Cable
(243) into the Single Pulley Block (27) as shown in Fig. 1.
2. Route the cable up and over the right side pulley in the Top Frame (5) as
shown in Fig. 2. Mount the pulley using one 3/8" X 2-3/4" Hex Bolt (89) and
one 3/8" Nylon Nut (107).
3. Continue to route the cable down to the pulley on the Base Frame (1) as
shown in Fig. 3. Mount the pulley using one 3/8" X 1-3/4" Bolt (91) and one
3/8" Nut (107).
4. Then route the cable up to the lower pulley in the Adjustable Pulley Block (25)
as shown in figure 4. Attach the pulley to the second hole from bottom. The
multiple holes are for cable adjustment. When cabling is complete, this pulley
can be moved upward to take up slack, or downward to gain length.
5. Continue to route the cable down to the pulley on the Base Frame (1) just
behind the weight stack, as shown in Fig. 5. Mount the pulley using one 3/8"
X 1-3/4" Bolt (91) and one 3/8" Nut (107).
6. Continue to route the cable underneath the weight stack and around the
horizontally mounted pulley on the Leg Press Main Frame (202). Mount the
pulley using one 3/8" X 1-3/4" Bolt (233) and one 3/8" Nut (241) as shown in
Fig. 6.
7. Continue to route the cable through the slot in Leg Press Main Frame (202),
and under and around (exiting on the top) the lowest pulley on the Rear Leg
Press Support (208) as shown in Fig. 7, Step 1. Mount the pulley using one
3/8" X 1-3/4" Bolt (233) and one 3/8" Nut (241).
8. Then route the cable under and around (exiting on the top) the right side (as if
sitting on seat) pulley mounted in Leg Press Main Frame (202) as shown in
Fig 7. Mount two pulleys here using one 3/8" X 2-3/4" Hex Bolt (232) and one
3/8" Nylon Nuts (241).
9. Route the cable in the same manner under and around the uppermost pulley
mounted on the Rear Leg Press Support (208) as shown in Fig. 7, Step 2.
Mount the pulley using one 3/8" X 1-3/4" Bolt (233) and one 3/8" Nut (241).
10. Route the cable in the same manner under and around the left side (as if
sitting on seat) pulley mounted in Leg Press Main Frame (202) as shown in
Fig 7.
11. Hook the ball end of the cable into the receptor on the Rear Leg Press
Support (208) as shown in Fig. 8.
Hint: When viewed from the side, the Leg Press Cable should be a series
of "loops". There should not be any "X's".
… 8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for BodyCraft Xpress Pro Legpress at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of BodyCraft Xpress Pro Legpress in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info