582143
4
Zoom out
Zoom in
Previous page
1/56
Next page
4
EN
the dryer. Dryer can get damaged if
metal reinforcements come loose and
break off during drying.
Never attempt to repair the product
yourself. Do not perform any
repair or replacement procedures
on the product even if you know
or have the ability to perform the
required procedure unless it is
clearly suggested in the operating
instructions or the published service
manual. Otherwise, you will be
putting your life and others' lives in
danger.
For failures that you cannot remedy
by applying the procedures in safety
instructions, turn off and unplug
the product and call the Authorized
Service Agent.
Do not reach into the machine when
the drum is spinning.
Do not use extension cords, multi-
plugs or adaptors to connect the
dryer to power supply in order to
decrease the risk of fire and electric
shock.
Never wash the product by spreading
or pouring water onto it! There is the
risk of electric shock!
The final step of the drying
programme, namely the cool-down
step is performed without applying
heat to ensure that the laundry items
are kept at a temperature that will
not damage them. If you open the
loading door before the cool-down
step completes, hot vapour will come
out.
A
Never stop the dryer before the
programme completes. If you must
do this, remove all laundry quickly
and lay them out to a suitable place
to dissipate the heat.
Always clean the lint filter before or
after each loading. Never operate the
dryer without the lint filter installed.
Clean inside and exhaust duct of the
product regularly. Do not allow fibre,
dust and dirt accumulation around
the exhaust exit and at adjacent
areas.
Power cable plug must be within easy
reach after installation.
Do not dry unwashed items in the
dryer.
Items soiled with cooking oils,
acetone, alcohol, fuel oil, kerosene,
stain removers, turpentine, paraffin
and paraffin removers must be
washed in hot water with plenty of
detergent before being dried in the
dryer.
Garments or pillows bolstered with
rubber foam (latex foam), shower
bonnets, water resistant textiles,
materials with rubber reinforcement
and rubber foam pads should not be
dried in the dryer.
Do not use fabric softeners and
anti-static products unless they are
recommended by the manufacturers
of the relevant product.
Use softeners, anti-static products
and etc. in accordance with the
instructions of their manufacturers.
Do not install the product behind a
door with a lock, sliding door or a
hinged door which can strike the
product.
Do not install or leave the dryer in
places where it will be exposed to
outdoor conditions.
Your product can be operated at
temperatures between +5°C and
+35°C. If the operating conditions fall
outside of this range, operation of the
product will be adversely affected and
it can get damaged.
Do not tamper with the controls.
Unplug the product when it is not in
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blomberg TKF 8451 A 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg TKF 8451 A 50 in the language / languages: English, Finnish as an attachment in your email.

The manual is 6,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info