Manual Blomberg TKF 8431 G (page 3 of 44) (English, German)

581565

Zoom out

Zoom in

1/44

1 Important safety information

This section includes safety information that will help

protection from risks of personal injuries or materialistic

damages. Failure to follow these instructions shall cause

any warranty and reliability commitment to become void.

General safety

• Never place the machine on a carpet-covered floor,

otherwise, lack of airflow beneath the machine may

cause electrical parts to overheat. This will cause

problems with your machine.

• If the power cable or mains plug is damaged, you

must call Authorised Service Agent for repair.

• The product should not be plugged in during

installation, maintenance and repair works. Such

works should always be made by the technical

service. Manufacturer shall not be held responsible

for damages arising from processes carried out by

unauthorised persons.

• Connect the product to a grounded outlet protected

by a fuse of suitable capacity as stated in the

technical specifications table.

• Operate your product at temperatures between +5°C

and +35°C.

• Do not use electrical devices in the product.

• Do not connect the air exit of the product to the

chimney holes which are used for the exhaust fumes

of the devices operating with gas or other types of

fuel.

• You must provide enough ventilation in order to

prevent gases exiting from devices operating with

other types of fuels including the naked flame from

accumulating in the room due to the back fire effect.

• Always clean the lint filter before or after each

• Never operate your dryer without the lint filter

installed.

• Do not allow fibre, dust and dirt accumulation around

the exhaust exit and at adjacent areas.

• Power cable plug must be within easy reach after

installation.

• Do not use extension cords, multi-plugs or adaptors

to connect the dryer to power supply in order to

decrease the risk of electric shock.

• Do not make any changes on the plug supplied with

the product. If it is not compatible with the socket,

have a qualified electrician change the socket with a

suitable one.

• Items cleaned or washed with gasoil/fuel oil, dry-

laundry solvents and other combustible or explosive

materials as well as the items that are contaminated

or spotted with such materials should not be dried in

the product since they emit flammable or explosive

vapor.

• Do not dry items cleaned with industrial chemicals in

the dryer.

• Do not dry unwashed items in the dryer.

• Items soiled with cooking oils, acetone, alcohol, fuel

oil, kerosene, stain remover, turpentine, paraffin and

paraffin removers must be washed in hot water with

plenty of detergent before being dried in the dryer.

• Garments or pillows bolstered with rubber foam

(latex foam), shower bonnets, water resistant textiles,

materials with rubber reinforcement and rubber foam

pads should not be dried in the dryer.

• Do not use fabric softeners and anti-static products

unless they are recommended by the manufacturers

of the fabric softener or the product.

• This product must be grounded. Grounding

installation decreases the risk of electric shock by

opening a path with low resistance for the electricity

flow in case of a malfunction or failure. Power cable

of this product is equipped with a conductor and a

grounding plug that allows for grounding the product.

This plug must be installed appropriately and inserted

into a socket which is grounded in accordance with

the local laws and regulations.

• Do not install the product behind a door with a lock,

sliding door or a door that has a hinge against the

hinge of the dryer.

• Do not install or leave this product in places where it

will be exposed to outdoor conditions.

• Do not tamper with the controls.

• Do not perform any repair or part replacing

procedures on the product even if you know or have

the ability to perform unless it is clearly suggested

in the operating instructions or the published service

manual.

• Inside and exhaust duct of the product must

be cleaned by the qualified service personnel

periodically.

• Wrong connection of grounding conductor of the

product can cause electric shock. If you have

any suspect about the grounding connection,

have it checked by a qualified electrician, service

representative or service personnel.

• Do not reach into the machine when the drum is

spinning.

• Unplug the machine when it is not in use.

• Never wash down the appliance with water! There

is the risk of electric shock! Always disconnect by

unplugging from the mains before cleaning.

• Never touch the plug with wet hands. Never unplug

by pulling on the cable, always pull out by grabbing

the plug only. Do not operate the machine if the

power cable or plug is damaged!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blomberg TKF 8431 G in the language / languages: English, German as an attachment in your email.

The manual is 5,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blomberg TKF 8431 G Manual

Product: