Manual Blendtec PROFESSIONAL 750 (page 9 of 12) (English)

626805

Zoom out

Zoom in

1/12

1514

A “RESET” error indicates a disruption in the normal operation of the electronic

blender controls� This is an uncommon error message, which is usually caused

by incoming power ﬂuctuations or spikes� This error message is cleared by turn-

ing off the blender for ten seconds (using the switch), then turning back on� If this

error is displayed immediately on start-up, or if it occurs regularly during normal

use contact your Blendtec service center for assistance��

BLADE STOPS: If the overload switch stops the blender, remove the blender jar

and carefully check for blockage of the blade� If no blockage is found, replace jar

and use the Pulse button on the touch pad to quickly pulse the blade through the

mixture� Once the blade spins freely, a programmed button may be used�

PROFESSIONAL 800™

Touch Error — This occurs when the side or space next to a control surface

button was touched� To avoid this message, touch the center of the desired button�

Overtemp Error — The motor is overheating� The blender has been disabled until

the unit cools to operating temperatures� Allow it to cool for at least 20 minutes�

Continued use may cause permanent damage to the motor�

Overload Error — There is an overload on the motor� Check the blender jar for

blockage and clear if necessary� Press Cancel to clear the overload message� If

overload condition re-occurs, contact Blendtec customer service (see page 17)�

Reset Errors — If the following error messages appear, reset the error by pressing

the cancel button or cycle the power by unplugging your blender and then plug-

ging it back in� If the error does not clear, contact your Blendtec service agent�

Error: Overtemp� condition detected

Error: Overload condition detected

Error: Temp� sensor not detected

Error: Zero crossing not detected

Error: Reset error detected

Error: Read/Write error detected

Error: Motor control error detected

Error: Invalid blend cycle

Error: Touch controller not detected

Error: Touch controller output is invalid

5.3 CLEANING TIPS AND CAUTIONS

• Do not use stiff bristled brushes or abrasive cloths/pads to clean the blender

base or jar as this will dull or scratch the surface�

• NEVER submerge the blender motor in water� Avoid submerging blender

jars for more than 5 minutes� Water penetration through the lower jar seals

will reduce he life of the jar� After cleaning, we recommend the blender jar

be stored upright�

• BLENDER JAR IS DISHWASHER SAFE—TOP RACK ONLY!

• Extreme temperatures damage the lower seal of the jar� We recommend hand

washing to prolong the life of the blender jar� We do not recommend the jar be

used for temperatures above boiling (212°F, 100°C)�

SECTION 6: TROUBLESHOOTING

While we don’t expect you to have any problems with your blender, sometimes

failures do occur� Use the following guidelines to see if the problem is easily

ﬁxed or requires service�

6.1 BLENDER MOTOR WILL NOT TURN ON (NO POWER)

If the blender motor will not turn on, try the following:

• Determine if the blender is receiving power by checking for the green light on

the Professional 750 or a wvhite power icon on the Professional 800�

• Make sure the blender is plugged in�

• Check your house circuit breaker switch or fuse to make sure it is set to the

ON position�

• Press the Power switch or Power icon, as applicable, on the machine�

• Unplug the power cord from the wall receptacle, wait 5 seconds, then plug

power cord back in�

6.2 ERROR MESSAGES ON DISPLAY

PROFESSIONAL 750™

The ”OVERTEMP” error message indicates an overheated condition has been

detected and the motor has been disabled until the unit cools to operating

temperatures� Allow to cool for at least 20 minutes�

The “OVERLOAD” error message indicates too heavy of a load on the motor�

This is usually caused by a blockage in the jar preventing the blender blades

from turning� Remove the jar from the blender to clear any blockage, then return

the jar to the blender base� Use PULSE to quickly pulse the blade through the

mixture� Once the blade spins freely a programmed button may be used� If

blender fails to start after following these steps, contact your Blendtec service

center for assistance�

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Blendtec PROFESSIONAL 750 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Blendtec PROFESSIONAL 750 Manual

Product: