716101

Blaupunkt WSSA 754501 Manual

21
Zoom out
Zoom in
Previous page
1/24
Next page
Product Specications
Voltage 18V DC
Rated speed 11000/min
Disc size 115 x 22.2mm
Sound Pressure Level LpA 88 dB(A) K: 3dB(A)
Sound Power Level LwA 99 dB(A) K=3dB(A)
Vibration Level 4.9m/s' K=1.5m/s'
Installing A Grinding Disc (Fig. 7)
WARNING: Always use the supplied wrench for slackening and tightening the clamping nut. You must ensure that the grinding
disc is positioned correctly before tightening the nut. Failure to do so will damage the disc and may result in serious injury when
the machine is switched on.
• Press the spindle lock button (10) and rotate the disc nut (2) until the spindle locks.
• Using the wrench supplied insert the pins into the holes on the disc nut. Turn the wrench anti· clockwise to release it.
• Place the grinding disc over the spindle with the concave side of the disc facing outward.
• Screw the clamp nut onto the spindle with the flat side of nut facing up. Fit the raised small diameter portion of the clamp nut
into the hole in the grinding disc. Tighten to finger tight only.
• Press the spindle lock button and rotate the grinding disc clockwise until the spindle locks.
• Securely tighten the disc nut with the wrench provided.
Operation
On/O Switch (Fig.14)
• To start the tool, pull back the safety lever (1) towards the rear of the machine and then squeeze the On/Off trigger (2).
• To stop the tool. release the trigger.
Grinding & Cut-o
Grinding discs should be a minimum of 3.9mm thickness and rated to a minimum of 11,000 RPM.
Cut-o discs should be a minimum of 1mm thickness and rated to a minimum of 11,000 RPM.
• Always select and use discs that are recommended for the material to be ground/cut.
• Secure all work before beginning the operation.
• Secure small workpieces in a vice or clamp to a workbench.
• For maximum control, hold the grinder in front and away from you with both hands, keeping the grinding disc clear of the
workpiece. Start your grinder and let the motor reach full speed. Gradually lower the grinder until the grinding disc contacts
the workpiece.
• Use just enough pressure to keep the grinder from vibrating or bouncing.
• Use light pressure when grinding jagged edges or loose bolts where there is potential for the grinder to snag on the metal
edge causing kickback.
• Lift the grinder away from the workpiece before turning it OFF.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt WSSA 754501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt WSSA 754501 in the language / languages: English, German as an attachment in your email.

The manual is 1,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info