394453

Blaupunkt vw 300 Manual

4
Zoom out
Zoom in
Previous page
1/38
Next page
4
+
-
4
+
-
4
+
-
8
SERIES
+
-
4
+
-
4
+
-
2
PARALLE
+
-
4
+
-
4
+
-
8
SERIES
+
-
4
+
-
4
+
-
2
PARALLE
ISOBARIC CONFIGURATION (TANDEM)
ISOBARIC WOOFER CONFIGURATIONS
Increasing in popularity in recent years is the compound woofer
design, more commonly known as the “Isobaric” design.
Isobaric actually means “constant pressure” which is the case
having two woofers moving an encapsulated pocket of air
between them in the same direction.
This arrangement acts like a single speaker which effectively
reduces the required box volumes for a subwoofer system by
50% which is substantial if you are space-limited. Unfortunately,
the trade-off for space is the 3 dB loss in efficiency but this is
usually recovered with increased amplifier power. Care must be
taken to avoid air leaks between the two woofers and final
speaker wiring and impedance loads must be carefully
watched.
SUBWOOFER ENCLOSURE CONSTRUCTION
Before starting final box assembly some basic construction issues should be mentioned:
– Infinite baffle construction in a car is done by simply cutting a piece of wood which will act as an
acoustical divider isolating the front and rear sound of the woofer. This piece of wood is mounted
inside the trunk of the car under the rear deck, or against the back of the rear seat, and should have
some kind of caulking to seal off all residual air leaks.
– Box construction can take on nearly any shape since we are dealing with low frequencies. Odd
shapes that are difficult to cut and glue should be avoided.
– Particle board, MDF, or high grade birch plywood are good materials to build boxes of thicknesses
of 19 to 25 mm.
– All seams in the box should be glued, screwed and caulked to prevent wall separation over time
due to vibration and environmental changes within the car.
– Cross bracing is important for large boxes to prevent wall vibration.
– Acoustical damping material (sheep wool or fibreglass batting 5 to 10 cm thick), attached to 50%
or more of the interior walls helps reduce box noise and also increases the box volume seen by
the woofer by 10 - 20%. The application of self-adhesive damping mats to the inside walls also
helps to eliminate wall resonances.
– The cables running from the amplifier to the subwoofer should be as short as possible with a cable
cross section of at least 4 mm2.
– The final box should be rock solid and air tight but should also remain serviceable should a woofer
be damaged for any reason.
– When possible, use 10 to 15 cm diameter port tubes to avoid wind noise from smaller diameter
sizes. PVC plumbing pipe in various diameters is available at most hardware stores with „elbow“
pipes allowing you to bend the tubes inside the box.
– Try to always use active (electronic) crossovers, such as those built into our
Velocity
amps, for
example.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt vw 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt vw 300 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 3,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info