614221

Blaupunkt TS-S1 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
TS-S1
ENGLISH
Temperature Sensor
Getting Started
1. Loosen screw at button to open the
cover. (Figure 1)
2. Insert the battery provided into the
battery compartment. (Figure 2)
3. Put the Control Panel into learning
mode.
4. Press the learn button to learn the
Temperature Sensor. (Figure 3).
5. Refer to Control Panel manual to
complete learning process.
Mounting Location
Do not mount close to heat souce,
air conditioner, door or window to
avoid rapid temperature change.
Avoid direct sunlight
Operation
The Temperature Sensor will
transmit reading to the Control
Panel every 30 minutes, or when
the learn button is pressed.
Temperature detection range: -10
℃ ~ 50℃.
Installation
Before installation, put the Control
Panel into Walk Test mode and press
the learn button at mounting location to
test signal range
1. The back cover has 2 knockouts for
mounting. (Figure 4)
2. Break through the knockouts; mark
the mounting location on using
knockouts as template. (Figure 5)
3. If required, drill holes into marked
location and insert wall plug.
(Figure 6)
4. Screw the back cover onto the
mounting location. (Figure 7)
5. Replace the front cover onto the
base.
Battery
The Temperature Sensor uses one
3.6V 1/2AA lithium battery. It features
low battery detection function to notify
the Control Panel when battery voltage
is low..
Specification
Environmental Condition:
-10°C to 50°C, relative humidity 85%
non-condensing.
Radio:
433 MHz
ESPAÑOL
Sensor de temperatura
Pasos iniciales
1. Aflojar el tornillo de la parte inferior
para abrir la tapa. (Figura 1)
2. Introduzca la pila suministrada en el
compartimento. (Figura 2)
3. Colocar el panel de control en
modo de aprendizaje.
4. Oprimir el botón de prueba del
sensor de temperatura para el
aprendizaje. (Figura 3).
5. Consulte el manual del panel de
control para completar el proceso
de aprendizaje.
Ubicación de montaje
No ubicarlo cerca de fuentes de
calor, aire acondicionado, puertas
o ventanas para evitar los
cambios bruscos de temperatura.
Evitar contacto directo de luz
solar.
Operación
El sensor de temperatura
transmitirá lecturas al panel de
control cada 30 minutos, o
cuando se oprima el botón de
prueba.
Rango de detección de
temperatura:-10℃ ~ 50℃.
Instalación
Antes de instalarlo, ajustar el panel de
control en modo Prueba de cobertura y
oprimir el botón de prueba del sensor
en la ubicación deseada para verificar
la intensidad de señal.
1. La tapa posterior tiene 2 orificios
ciegos para hacer el
montaje.(Figura 4)
2. Romper los orificios ciegos y
usarlos como plantilla para marcar
los puntos sobre el sitio. (Figura 5)
3. Si es necesario, perforar los
orificios de montaje sobre las
marcas realizadas e insertar los
tacos de pared.(Figura 6)
4. Atornillar la tapa posterior al sitio
elegido. (Figura 7)
5. Poner la tapa frontal sobre la base.
Baterías
El sensor de temperatura utilize una
pila de litio tipo 1/2AA de 3.6 V. Tiene
la función de detección de batería baja
para notificar el panel de control.
Especificaciones
Condiciones ambientales:
-10°C hasta 40°C, humedad relativa del
85% sin condensación.
Frecuencia:
433 MHz
Figure 1 / Figura 1
Figure 5 / Figura 5
Figure 2 / Figura 2
Figure 3 / Figura 3
Figure 4 / Figura 4
Figure 6 / Figura 6
Figure 7 / Figura 7
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt TS-S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt TS-S1 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt TS-S1

Blaupunkt TS-S1 User Manual - German - 2 pages

Blaupunkt TS-S1 User Manual - Dutch - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info