614664

Blaupunkt Stockholm RCR42 Manual

2
Zoom out
Zoom in
Previous page
1/15
Next page
GB
Notes on Safety
Instructions for installation and connection.
Disconnect the battery ground wire during installation and connection.
This car radio can be used for both 2 x 20 or 4x7watts operation. For
this, the corresponding connector box has to be mounted to the car radio.
When drilling a hole, be sure not to damage any vehicle parts (battery,
cable, fuse case, etc.).
The positive cable must have a cross-section of at least 1 mm. The unit
is protected by a quick-acting fuse of 5 A.
If you use a motor or electronic antenna, it will be activated when the TIM
function is switched on, which will lead to a certain current drain.
Note:
By means of the support included in delivery you can mount the set in cars
with a DIN car radio cut-out of 182 x 53 mm, an installation depth of 165
mm and an instrument panel thickness around the fixing clips of 1 - 20
mm, see fig. 1.
For cars with other cut-out dimensions Blaupunkt delivers car-specific
installation kits for common car types for 50/52 mm sets. Use enclosed
distance plates only for installation kits of 52 mm sets.
Please check the dimensions and, if necessary, use a car-specific
installation kit, e. g. VW Golf II / Jetta II/: 7 608 3824 73.
When using installation sets for units of 52 mm four distance plates, order
number 8 601 055 056 must be used, fig. 1a.
Preparation of car radio installation
Install the car radio into the DIN cut-out provided in your car’s dashboard
ex factory.
Prepare the car radio DIN cut-out (unlock shelf or dummy cover) or cut
out the car radio compartment to 182 x 53 mm.
Grasp behind the car radio cut-out and check how many of the fixing
strips of the car radio support may be bent.
Note:
Try to bend as many fixing strips as possible.
Insert the support into the cut-out and bend the appropriate fixing strips
with a screwdriver, see fig. 1, 2.
Connection
Connection overview .................................................................... fig. 4
Notes on connection ..................................................................... fig. 5
Connection of equalizer and amplifier .......................................... fig. 6
Connection CD-Player .................................................................. fig. 7
Loudspeaker connection:
4 speakers (4 Ω/7 W).................................................................... fig. 9
2 speakers (4 Ω/22 W)................................................................ fig. 10
Depending on the speaker equipment of the respective vehicle either the
2- or 4-channel connector box has to be exchanged (the 2 x 20 watts box
is marked).
Change connecting box
1. Loosen the screw and unlock the top and bottom support springs by
lifting them, see fig. 15.
2. Pull out the connecting box, see fig. 16.
3. Position the connecting box with the sides in the correct position and
parallel to the cabinet, and push it in carefully, see fig. 17.
4. Tighten the screw and hook in the top and the bottom support screw.
5. Replace the fuse of the connecting box.
Important notes!
If these notes are disregarded, there is danger of destroying the
final stages.
Do not connect speaker outputs to ground!
Connection with multiple plug installed ex factory
Audi, VW
Passive loudspeaker system:
Use QuickFit or adapter cable.
Active loudspeaker system:
Pin 1, 2, 3 and 4 of the +/- connector (8 pins, black) shall be disconnected.
Connect the wire at pin 3 to pin 5. Connect the wire at pin 4 to pin 7.
Opel
1. Remove the car radio support prior to the installation. Disconnect the
compact connector and the antenna cable.
2. Check the compact connector. Pin 1, 2 and 3 of chamber 3 (8 pins)
must not be connected.
3. Exchange pin 4 and pin 7 of chamber 3 against each other.
Ground cable
Do not connect the ground cable to the negative pole of the battery.
Route the ground cable to a suitable ground point (car body screw, car
body metal sheet) and shorten it accordingly.
Remove the insulation from the ground cable and attach the forked cable
lug (if necessary, solder it).
Scratch off the paint from the contact area of the ground point and
lubricate it with graphite grease (important for good ground contact).
Screw on the ground cable.
Positive cable (ACC 12 V) (ignition)
Connect the positive cable together with distributor to pin 30 (constant
power) or pin 15 (positive line connected via ignition) of the fuse holder
behind the fuse.
Permanent plus connection (Battery 12 V)
Connect the permanent plus terminal together with the cable and cable
clamp to a fuse-protected positive line (e.g. clock, warning flasher).
Control cable (Power Antenna +)
Connect the antenna’s control cable to the control cable of the car
stereo when installing a fully automatic motor antenna or electronic
window antenna. The switching line must not be used as the switching
voltage for an amplifier, since the control cable can be live even if the
set is off with the TIM function being activated. The amplifier would then
be activated. The control cable is fuse-protected.
Lighting connection (Illumination)
Lighting connection for vehicles with adjustable dashboard lighting (plus-
controlled).
Amplifier
The preamp jack is not occupied. Amplifier connection via loudspeaker
outputs only. To set up the amplifier’s switching voltage, attach the
enclosed cable to chamber 1 of the power supply connection block.
Car radio installation
Insert the car radio from the front into the support and push in until the
stop springs on the sides engage right and left (distinct click to be heard).
Removal of the car radio
Insert the brackets right and left into the provided trimplate holes and
push in until you hear a distinct click (lateral springs are unlocked).
Using both brackets (see fig. 5), pull the unit out.
Note:
Locked brackets can only be removed after taking out the unit.
QuickOut (shuttle support)
Use the car radio specific QuickOut support.
Modifications reserved.
+12V
per. +12V
+12V
Preamp.
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt Stockholm RCR42 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt Stockholm RCR42 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info