614234

Blaupunkt PB-S1 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
PB-S1
ENGLISH
Panic Button
Getting Started
1. Loosen the screw at button to open
back cover. (Figure 1)
2. Insert the battery provided and
close the back cover. (Figure 2)
3. Put the Control Panel into learning
mode.
4. Press and hold the button for about
3 seconds to learn the Panic Button.
(Figure 3)
5. Refer to Control Panel manual to
complete learning process.
Mounting Location
Mount in a convienient location for
easy access, such as living room
or bedroom
Operation
Press and hold the button for 3
seconds to activate a Panic alarm
regardless of system mode.
The LED will light up when the
button is pressed.
Installation
Before installation, put the Control
Panel into Walk Test mode and press
the button at mounting location to test
signal range
1. The Panic Button has 2 knockouts
on the inside of back cover..
(Figure 4)
2. Break through the knockouts; mark
the mounting location on using
knockouts as template. (Figure 5)
3. If required, drill holes into marked
location and insert wall plug.
(Figure 6)
4. Screw the back cover onto the
mounting location. (Figure 7)
5. Replace the front cover onto the
base.
Instead of screw mounting, you
can also use the double side
adhesive tape included in the
package to install the accessory.
Battery
The Temperature Sensor uses one
CR2032 3V lithium battery. It features
low battery detection function to notify
the Control Panel when battery voltage
is low..
Specification
Environmental Condition:
-10°C to 40°C, relative humidity 85%
non-condensing.
Radio:
433 MHz
ESPAÑOL
Botón de pánico
Pasos iniciales
1. Aflojar el tornillo de la parte inferior
del botón para abrir la tapa
posterior.(Figura 1)
2. Introduzca la pila suministrada y
cerrar la tapa posterior. (Figura 2)
3. Colocar el panel de control en
modo de aprendizaje.
4. Mantener oprimido el botón durante
3 segundos para el aprendizaje del
botón de pánico.(Figura 3)
5. Consulte el manual del panel de
control para completar el proceso
de aprendizaje.
Ubicación de montaje
Ubicar el botón en lugar
conveniente y de fácil acceso,
como la sala o dormitorio.
Operación
Mantener oprimido el botón
durante 3 segundos para disparar
la alarma de pánico
independientemente del modo del
sistema.
El LED se iluminará cuando el
botón es oprimido.
Instalación
Antes de instalarlo, ajustar el panel de
control en modo Prueba de cobertura y
oprimir el botón de prueba en la
ubicación de montaje para verificar la
intensidad de señal.
1. El botón de pánico tiene 2 orificios
ciegos en la tapa posterior.(Figura
4)
2. Romper los orificio s ciegos y
usarlos como plantilla para marcar
los puntos sobre el sitio a instalar.
(Figura 5)
3. Si es necesario, perforar los
orificios de montaje sobre las
marcas realizadas e insertar los
tacos de pared. (Figura 6)
4. Atornillar la tapa posterior en el sitio
escogido. (Figura 7)
5. Poner la tapa frontal sobre la base.
Si lo prefiere, puede utilizar
también la cinta adhesiva de
doble faz incluida en el empaque.
Batería
El botón de pánico utiliza una pila de
litio CR2032 de 3V. Tiene la función de
detección de batería baja para notificar
el panel de control.
Especificaciones
Condiciones ambientales:
-10°C hasta 40°C, humedad relativa del
85% sin condensación.
Frecuencia:
433 MHz
Figure 1 / Figura 1
Figure 5 / Figura 5
Figure 2 / Figura 2
Figure 3 / Figura 3
Figure 4 / Figura 4
Figure 6 / Figura 6
Figure 7 / Figura 7
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt PB-S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt PB-S1 in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt PB-S1

Blaupunkt PB-S1 User Manual - German - 1 pages

Blaupunkt PB-S1 User Manual - Dutch - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info