517617
78
Zoom out
Zoom in
Previous page
1/78
Next page
IM LIEFERUMFANG ENTHALTENE BAUTEILE
A . MOTORRAD LENKERSOCKEL (ANZ. 1)
B. 1/4”-20 SELBSTSICHERNDE MUTTER, VERZINKT (ANZ. 2)
C. GUMMIKAPPE FÜR 1/4” MASCHINENKOPFSCHRAUBE (ANZ. 2)
1/4-20X 1,06 ID X 1,75 BÜGELSCHRAUBE, VERZINKT (ANZ. 1)
E. 1/4”-20 2” SECHSKANTKUGEL-MASCHINENKOPFSCHRAUBE (ANZ. 2)
F. 6MM X 55MM MASCHINENKOPFSCHRAUBE (ANZ. 2)
G. NYLON-DISTANZHALTER ½” OD X .257” ID X ½”LG (ANZ. 2)
H.1/4” ST
ST
SICHERUNGSSCHEIBEN (ANZ. 2)
KUGELSOCKELINSTALLATION AUF BREMS-/KUPPLUNGSFLÜSSIGKEITSBEHÄLTER
FINDEN SIE DEN BREMS-/KUPPLUNGSFLÜSSIGKEITSBEHÄLTER AUF DEM LENKER IHRES
MOTORRADS. DIESER IST MIT ZWEI SCHRAUBEN BEFESTIGT. (JE NACH MOTORRADTYP
KÖNNEN SICH DIESE SCHRAUBEN HINTER EINER PLASTIK- ODER METALLBLENDE BEFINDEN.
ENTFERNEN SIE DIESE BLENDE, UM DIE SCHRAUBENKÖPFE FREIZULEGEN.) MARKIEREN
SIE VOR DEM ENTFERNEN DER SCHRAUBEN DIE POSITION DES MONTA
GESATZES AUF DEM
LENKER, FALLS SIE DIESEN ZU EINEM SPÄTEREN ZEITPUNKT ERNEUT MONTIEREN MÜSSEN.
1. ENTFERNEN SIE EINE DER SCHRAUBEN UND VERGLEICHEN SIE DAS GEWINDE MIT DEN
BEILIEGENDEN SCHRAUBEN (E oder F). LEGEN SIE DIE 2 PASSENDEN SCHRAUBEN,
2 DISTANZHALTER (G) UND 2 SICHERUNGSSCHEIBEN (H) BEREIT.
2. SCHIEBEN SIE JEWEILS EINE SICHERUNGSSCHEIBE (H)
AUF DIE 2 SCHRAUBEN
U
ND STECKEN SIE DIE SCHRAUBEN DURCH DIE LANGLÖCHER DES LENKER-
SOCKELS (A). DIE SCHRAUBENKÖPFE SOLLTEN AUF DER SEITE DES SOCKELS MIT
DEM RAM LOGO SICHTBAR SEIN.
3. POSITIONIEREN SIE DIE DISTANZHALTER (G) AUF DEN GEWINDEN DER BEIDEN
SCHRAUBEN UND LEGEN SIE DEN MONTAGESATZ BEISEITE.
4. ENTFERNEN SIE DIE LETZTE SCHRAUBE. HALTEN SIE DIE URSPRÜNGLICHE BREMS-/
KUPPLUNGSGRUPPE DABEI FEST.
HALT
EN SIE DEN MONTAGESATZ ZUSAMMEN,
WÄHREND SIE DIE SCHRAUBE ENTFERNEN, UM KEINE BAUTEILE ZU VERLIEREN. LEGEN
SIE DIE SCHELLE UND FABRIKSCHRAUBEN BEISEITE. IST DER MOTORRADTYP NICHT FÜR DIE
LÄNGE DER SCHRAUBEN IN IHREM RAM MONTAGEKIT
AUSGELEGT, DARF DIE WERKSEITIG GELIEFERTE SCHELLE NICHT DEMONTIERT WERDEN.
5. NEHMEN SIE IHREN RAM MONTAGESATZ VORSICHTIG HOCH UND DREHEN SIE DIE RAMSCHRAUBEN
VON HAND IN DIE GEWINDELÖCHER IHRER BREMSEN/KUPPLUNGSFLÜSSIGKEITSBEHÄLT
ER.
6. ZIEHEN SIE DIE SCHRAUBEN MIT EINEM INBUSSCHLÜSSEL FEST, BIS DER MONTAGE-
SATZ FEST MONTIERT IST.
7. BEWAHREN SIE UNGENUTZTE BAUTEILE ODER KOMPONENTEN FÜR EINE EVENTUELLE
SPÄTERE VERWENDUNG AUF.
KUGELSOCKELINSTALLATION MIT BÜGELSCHRAUBEN:
1. WÄHLEN SIE EINE STELLE AUF DEM LENKER AUS, AN DER DIE WERKSAUSSTATTUNG
NICHT BEEINTRÄCHTIGT
WIRD ODER A
NZEIGEN BLOCKIERT WERDEN. SICHERHEIT
GEHT VOR.
2. POSITIONIEREN SIE DIE BÜGELSCHRAUBE (D) AUF DEM LENKERSOCKEL UND RICHTEN
SIE DIE GEWINDEBOHRUNGEN MIT DEN LÖCHERN DES LENKERSOCKELS (A) AUS.
3. SCHIEBEN SIE DIE BASIS MIT DER AUSSPARUNG DEM LENKERSOCKEL ZUGEWANDT ÜBER DIE
GEWINDELÖCHER.
4. SCHRAUBEN SIE BEIDE MUTTERN (B) VON HAND BIS ZUM ANSCHLAG FEST.
5. ZIEHEN SIE BEIDE MUTTERN MIT EINEM
STECK- ODER RINGSCHLÜSSEL
IM WECHSEL FEST, BIS DER
KUGELSOCKEL FEST AUF DEM LENKER MONTIERT IST.
6. STELLEN SIE SICHER, DASS SIE MIT DER POSITION DES KUGELSOCKELS ZUFRIEDEN SIND, BEVOR SIE
DIE MUTTERN ENDGÜLTIG FESTZIEHEN.
7. ZIEHEN SIE DIE MUTTERN NICHT ZU FEST AN. DAS ANZIEHEN DER MUTTERN ÜBER EINEN DREHMOMENT
VON 5 LB/FT3. KANN ZU RISSBILDUNGEN IM SOCKEL FÜHREN. ÜBERMÄSSIGES ANZIEHEN KANN ZUDEM
DEN
L
ENKER BESCHÄDIGEN. ZIEHEN SIE DIE MUTTERN VORSICHTIG FEST.
8. STECKEN SIE ABSCHLIESSEND BEIDE GUMMIKAPPEN (C) AUF DIE FREILIEGENDEN GEWINDE DER BÜGEL
SCHRAUBE.
DER HERSTELLER ÜBERNIMMT KEINE HAFTUNG FÜR SCHÄDEN AUFGRUND TECHNISCHER VERÄNDERUNGEN, UNSACHGE-
MÄSSER INSTALLATION, STRASSENSCHÄDEN ODER UNFÄLLEN. RAM HAFTET NICHT FÜR VERLETZUNGEN, VERLUSTE ODER
SCHÄDEN, DIE DIREKT ODER INDIREKT DURCH U
NSACHGEMÄSSE INSTA
LLATION ODER UNFÄHIGKEIT DIESES PRODUKT ZU
VERWENDEN ENTSTEHEN. VOR DER VERWENDUNG MUSS DER NUTZER SICH VERGEWISSERN, OB SICH DAS PRODUKT FÜR
DIE GEPLANTE VERWENDUNG EIGNET UND MUSS SICH DER DAMIT VERBUNDENEN RISIKEN SOWIE DER SICH DARAUS ERGE-
BENDEN MÖGLICHEN HAFTUNG BEWUSST SEIN.
MONTAGEANLEITUNG
78


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt MotoPilot software at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt MotoPilot software in the language / languages: German as an attachment in your email.

The manual is 3,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info