614226
1
Zoom out
Zoom in
Previous page
1/2
Next page
Wireless PIR Motion Sensor (IR-S1)
P
P
a
a
r
r
t
t
s
s
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
1. Learn/Test Button & LED indicator
Press the button to transmit a learn/test code and enter Test
mode for 3 minutes. The LED will light up whenever a movement
is detected under Test mode.
2. Battery Insulator
3. Supervision Enable/Disable Jumper Switch
(JP2)
4
. High/Low Sensitivity Jumper Switch (JP3)
5. Tamper Switch
The Tamper switch protects the PIR from unauthorized cover
opening.
P
P
a
a
c
c
k
k
a
a
g
g
e
e
C
C
o
o
n
n
t
t
e
e
n
n
t
t
1 x PIR Sensor
4 x wall plugs and screws
2 x 1.5V alkaline batteries (pre-installed)
Supervision Enable/Disable Jumper Switch (JP2)
If enabled, the PIR sensor will transmit supervision signal to
Control Panel periodically for the sensor to monitor PIR sensor
condition.
Jumper set to ON = supervision function is Disabled (Default)
Jumper set to OFF = supervision function is Enabled
High/Low Sensitivity Jumper Switch (JP3)
Jumper set to ON = PIR sensitivity is set to High
Jumper set to OFF= PIR sensitivity is set to Low (Default)
Put the Control Panel into learning mode, then press the learn
button to transmit learn code. Please refer to Control Panel
manual for to complete the learning process.
The PIR Sensor has knockouts on the back where plastic is
thinner. The 2 center knockouts are for flat wall mounting, and the
4 side knockouts are for corner mounting.
1. Break through the knockouts; use the knockouts to mark
position on the wall or corner.
2. Drill holes into the wall or corner using the knockouts as
template.
3. Fix the PIR Sensor base onto the wall with the screws and
plugs provided.
4. Replace the PIR Sensor cover onto the base.
S
S
l
l
e
e
e
e
p
p
T
T
i
i
m
m
e
e
r
r
The PIR features a “sleep time” of approximately 1 minute for
power conservation. After transmitting a detected movement, the
PIR will not retransmit for 1 minute. Any further movement
detected during this sleep period will extend the sleep time by
another minute. In this way continuous movement in front of a
PIR will not unduly exhaust the battery.
T
T
e
e
s
s
t
t
M
M
o
o
d
d
e
e
Press the Test Button to enter Test mode for 3 minutes. Sleep
timer will be disabled under Test mode, and the LED indicator will
flash every time a movement is detected. Use the Test mode to
determine PIR detection coverage and plan the installation
location accordingly.
L
L
E
E
D
D
I
I
n
n
d
d
i
i
c
c
a
a
t
t
o
o
r
r
Off Normal Operation
On (2 seconds) - When Tamper Switch is triggered
- Movement detection under low battery,
tamper triggered, or Test mode.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
Jumper On
The jumper link is inserted
connecting the two pins
Jumper Of
f
if the jumper link is removed
or parked on one pin.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Surface Fixing
Knockouts x 2
(Inside)
Corner Fixing
Knockouts x 4
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Blaupunkt IR-S1L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Blaupunkt IR-S1L in the language / languages: English as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Blaupunkt IR-S1L

Blaupunkt IR-S1L User Manual - German - 2 pages

Blaupunkt IR-S1L User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info