577930
5
Zoom out
Zoom in
Previous page
1/72
Next page
5
ENGLISH
(Original instructions)
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Labels on tool
The following pictograms are shown on the tool:
;
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Electrical safety
@
This product must be earthed. Always check that
the power supply corresponds to the voltage on the
rating plate.
Power plugs must match the outlet. Never modify the plug in
any way. Unmodied plugs and matching outlets will reduce
risk of electric shock.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Extension cables & Class 1 product
u A 3-core cable must be used as your appliance is earthed
and of Class 1 construction.
u Up to 30m (100 ft) can be used without loss of power.
Voltage Drops
Inrush currents cause short-time voltage drops. Under unfa-
vourable power supply conditions, other equipment may be
affected. For example, articial lighting will show a temporary
drop in magnitude when the machine is switched on. If the
system impedance of the power supply is lower than 0.19 Ω,
disturbances are unlikely to occur.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Heat control knob
3. Nozzle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting an accessory
A selected range of accessories can be obtained from your
local retailer.
w Cone nozzle: Concentrates the air stream on a smaller
area.
w Fish tail: Spreads the air stream over a wider area
w Spoon reector: For soldering pipes.
w Glass protector: For the protection of glass during paint
stripping.
w Scraper: For the removal and stripping paint and
varnish.
u Fit the connecting piece of the accessory over the nozzle
(3).
Use
Setting the temperature (g. A)
u To increase the temperature setting, turn the heat control
knob (2) clockwise.
u To reduce the temperature setting, turn the heat control
knob anti-clockwise.
Switching on and off
u To switch the tool on, set the on/off switch (1) to position I.
u To switch the tool off, set the on/off switch to position O.
Warning! This tool is tted with a thermal cut out to prevent
the tool from over heating. If during use the tool becomes too
hot through being used for prolonged periods or being used
too close to the work surface then the tool will switch off.
When this occurs, switch the tool off and disconnect from the
supply mains. Place the tool in its rest position and allow at
least 30 mins for the tool to cool down before attempting to
switch the tool back on. Once the tool cools it will switch on
again. Never leave the tool un-attended when connected to
the mains.
Using the tool
Your tool is tted with a thermostat for your safety. Using the
tool continuously for very long periods or other severe duty
cycles may cause the tool to overheat and stop working. It is
therefore recommended that you allow the tool to cool down at
regular intervals during use.
u Allow the tool to heat up for a few seconds before use.
u At rst use some smoke may emit from the nozzle. This is
normal and will soon decrease.
u Your tool is capable of many different heat settings using
a combination of the two settings on the trigger and the
variable heat control dial.
u Use a low temperature setting for drying paint and varnish,
removing stickers, shrinking insulation tubes, and thawing
frozen pipes.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KX2000K T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KX2000K T3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info