581144
4
Zoom out
Zoom in
Previous page
1/8
Next page
4
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for hand-held saws
Warning! Contact with or inhalation of dusts arising
from cutting applications may endanger the health of the
operator and possible bystanders. Wear a dust mask
specifically designed for protection against dust and
fumes and ensure that persons within or entering the
work area are also protected.
Do not use the tool for purposes not intended, for
example, do not cut tree limbs or logs.
Always use the appropriate type of saw blade for the
workpiece material and type of cut.
Only use saw blades in perfect condition.
Always switch the tool off and wait for the saw blade to
come to a complete standstill before putting the tool down.
When not in use, the tool should be put down on its side.
Keep your hands well clear of the saw blade while working.
Whenever possible, use clamps or a vice to secure the
workpiece.
Before use, make sure that the cutting area is free of
obstacles, especially on the reverse side of the cut.
Before sawing in walls or floors, be aware of the location
of hidden pipes and wiring.
Do not use the tool while in a tree, on a ladder or on any
other unstable surface.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised
to ensure they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-off button
3. Blade release button
Assembly
Warning! Before assembly, make sure that the tool is switched
off and unplugged.
Fitting and removing a saw blade (fig. A - C)
Saw blade
4. Large capacity blade
Fitting
Place the blade over the location pin (5).
Rotate the blade upward through 90° until it is fully
located in the saw blade slot (6) and the location pin is in
the locked position.
Make sure the blade is securely fitted by trying to remove
it without depressing the blade release button (3).
If you are unable to fit the blade, check if the location pin is in
the correct position as shown in fig. C. If it is not, keep the
blade release button depressed and use a screwdriver to turn
the location pin into the correct position.
Removing
Keep the blade release button (3) depressed and rotate
the blade downward through 90°.
Take the blade sideways off the location pin and slide it
out of the tool.
Release the blade release button.
Use
Warning! Let the tool work at its own pace. Do not overload.
Do not touch the saw blade immediately after the
operation as it might be hot.
Switching on and off (fig. D)
To switch the tool on, push the two lock-off button (2) into
the unlock position and squeeze the variable speed switch
(1).
To switch the tool off, release the variable speed switch.
Sawing (fig. E)
If possible, always hold the tool with both hands.
Let the blade run freely for a few seconds before starting
the cut.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KS1880EC T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KS1880EC T1 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KS1880EC T1

Black Decker KS1880EC T1 User Manual - English, German, Dutch, Danish, French, Italian - 56 pages

Black Decker KS1880EC T1 User Manual - Polish - 12 pages

Black Decker KS1880EC T1 User Manual - Portuguese, Swedish, Spanish, Norwegian, Finnish - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info