Manual Black Decker kc 9662 c (page 3 of 58) (English, German, Dutch, French, Italian, Portuguese, Spanish)

387092

Zoom out

Zoom in

1/58

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the

recommended

fuse

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

Mains plug replacement (UK only)

Should your mains plug need replacing and you are

competent to do this, proceed as instructed below.

If you are in doubt contact a Black & Decker service

centre or a qualified electrician.

• Disconnect the plug from the power supply.

• Cut off the plug and dispose of safely. A plug

with bared copper conductors is very dangerous

if engaged in a live socket outlet.

• Only fit 13 amp BS1363A approved plugs fitted

with the correctly rated fuse.

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see diagram). Brown is for ‘live’ (L)

and blue is for ‘neutral’ (N).

• Before replacing the top cover of the mains plug

ensure that the cable restraint is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

• Warning! Never connect live or neutral wires

to the earth pin marked ‘E’ or .

Extension cables

You can use up to 100 feet (30 metres) of

Black & Decker 2-core extension cable without

undue loss of power.

Note: An extension cable should not be used unless

absolutely necessary. Use of an improper extension

cable could result in a risk of fire and electric shock.

If an extension cable must be used, make sure it is

properly wired and in good electrical condition.

Description (Fig. A)

1. Power pack

2. Power pack release button

3. Switch

4. Forward/reverse/lock lever

5. Two gear selector

6. Storage for bit and key (bit only on

keyless chuck models)

7. Clutch/hammer mechanism

(where applicable)

8. Keyed chuck

9. Keyless chuck

10. 1 hour charger

11. 3 hour charger

Charging the batteries (Fig. B1 & 2)

The batteries in your drill/driver are not

charged when supplied as new.

Before attempting to charge your drill,

read thoroughly all of the preceding and

following instructions!

To charge your drill, follow the steps below:

• Put the forward/reverse lever in the

“OFF” (centre) position, and remove any

accessories from the chuck.

• To release the battery, press the buttons

and pull the battery out (Fig. B1).

• Plug the charger into a standard

electrical outlet.

• Place the battery in the charger

as indicated (Fig. B2).

During charging, the charger and battery

may feel warm to touch; this is quite normal.

• Allow the battery to remain in this

condition for at least 3-5 hours for a

3 hour charger or until the red light goes

out on a 1 hour charger. It will then be

ready for use.

• Disconnect the supply before making or

breaking connections to the battery.

Important charging notes

• Longest life and best performance can be

obtained if the energy pack is charged when the

air temperature is about 24°C. Do not charge the

energy pack in an air temperature below 5°C,

or above 35°C.

• Whilst charging, the charger and the energy pack

may become warm to touch. This is a normal

condition and does not indicate a problem.

• If the energy pack does not charge properly,

proceed as follows:

• Check the current at the socket by plugging

in a lamp or other appliance.

• Move the charger and power pack to a

location where the surrounding air

temperature is about 24˚C. In an extremely

warm environment the energy pack may be

too hot to permit charging.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker kc 9662 c in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker kc 9662 c Manual

Product: