578176
4
Zoom out
Zoom in
Previous page
1/56
Next page
4
ENGLISH
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from those intended could result
in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional safety instructions for sanders
Warning! Contact with or inhalation of dusts arising
from sanding applications may endanger the health of the
operator and possible bystanders. Wear a dust mask
specifically designed for protection against dust and
fumes and ensure that persons within or entering the
work area are also protected.
Thoroughly remove all dust after sanding.
Take special care when sanding paint which is possibly
lead based or when sanding some woods and metal
which may produce toxic dust:
- Do not let children or pregnant women enter the work
area.
- Do not eat, drink or smoke in the work area.
- Dispose of dust particles and any other debris safely.
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Features
1. On/off switch
2. Lock-on button
3. Variable speed control knob (KA85E)
4. Tension lever
5. Dust extraction outlet
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting a sanding belt (fig. A)
Warning! Never use the tool without a sanding belt.
Pull the tension lever (4) outward to release the tension
on the sanding belt (6).
Remove the old sanding belt.
Place a new sanding belt over the rollers. Ensure that the
arrow on the sanding belt points in the same direction as
the arrow on the tool.
To ensure a correct tracking, the sanding belt must be
centred over the rollers.
Push the tension lever (4) inward to tension the sanding
belt.
Fitting and removing the dustbag (fig. B)
Slide the dustbag (7) over the dust extraction outlet (5).
To remove the dustbag, slide it off the outlet.
Use
Warning! Let the tool work at its own pace. Do not overload.
KA85E - Variable speed control (fig. C)
The variable speed control allows you to adapt the speed of
the tool to the workpiece material.
Set the control knob (3) to the desired setting. Use a high
speed for wood, medium speed for veneer and synthetics
and low speed for acrylic glass, non-ferrous metals and
for removing paints.
Switching on and off
To switch the tool on, press the on/off switch (1).
For continuous operation, press the lock-on button (2) and
release the on/off switch.
To switch the tool off, release the on/off switch.
To switch the tool off when in continuous operation,
press the on/off switch once more and release it.
Emptying the dustbag
The dustbag should be emptied every 10 minutes.
Unzip the bag and empty it before continuing.
Hints for optimum use
Always hold the tool with both hands.
Do not exert too much pressure on the tool.
Regularly check the condition of the sanding belt.
Replace when necessary.
Always sand with the grain of the wood.
When sanding new layers of paint before applying
another layer, use extra fine grit.
On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
Consult your retailer for more information on available
accessories.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker KA85 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker KA85 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker KA85 T1

Black Decker KA85 T1 Quick start guide - English - 12 pages

Black Decker KA85 T1 User Manual - Turkish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info