Manual Black Decker GA100 T2 (page 5 of 52) (English, German, Dutch, French, Italian, Portuguese, Spanish)

586385

Zoom out

Zoom in

1/52

• Locate the cable and cable protector into the

body correctly (see opposite, figure a). Then fit

the cable clamp over the outer sheath of the

cable and screw down until the screws are fully

home. Failure to do this may result in the cover

not fitting correctly to the connector body.

• Before replacing the cover of the ‘female’

connector make sure that the cable clamp is

holding the outer sheath of the cable firmly with

screws fully home and that the two leads are

correctly fixed at the terminal screws and are not

taut (see opposite, figure a).

• Place the cover onto the body assembly

ensuring that it seats flat, then retighten the

fixing screw into the nut until the cover is

securely held (see opposite, figure c).

• Finally check that the cable protector is secure

and that there are no gaps between the cover

and the connector body.

terminal screws

clamping washers

connector body fixing screw

6mm

cable

clamp cover

cable

protector

Fitting a new mains plug (UK only)

Fitting the ‘female’ connector

(UK only)

To remove the cover, unscrew the fixing screw until it

is free of the nut which is located in the hexagonal

recess on the underside of the connector.

Take care not to lose the nut if it falls out.

There is no need to completely remove the fixing

screw as it is intended to remain captive in the cover.

The cover can now be removed by applying

pressure as follows.

apply

pressure here

The extension cable contains two wires which are

colour coded for easy recognition; brown is for ‘Live’

(L) and blue is for ‘Neutral’ (N). The female connector

is marked ‘L’ for live and ‘N’ for neutral. These

markings are located inside the body near the

terminal screws (see opposite, figure a). With the

connector cover removed, lift out the cable protector

and proceed as follows:

• Pass the cable through from the narrow end of

the cable protector (see opposite, figure a).

• Prepare the cable ends to the specified strip

lengths (see opposite, figure b).

• Remove cable clamp (see opposite, figure a).

Take care of loose parts.

• To connect the extension cable to the connector

terminals, unscrew the terminal screws until the

clamp washers have lifted just enough to enter

the conductor between the raised washer and

the terminal (see below). Connect the brown

lead to ‘L’ and the blue lead to ‘N’. N.B. There is

no need to remove the terminal screws.

Connections are not to be made under the

screw heads.

terminal screw

clamp terminal

washer conductor position

to left of screw

ENGLISH

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit the

recommended

fuse

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GA100 T2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GA100 T2

Black Decker GA100 T2 User Manual - Danish, Swedish, Norwegian, Finnish - 22 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GA100 T2 Manual

Product: