Manual Black Decker CD70CKA (page 4 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

601834

Zoom out

Zoom in

1/56

ENGLISH

g. Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the

manner intended for the particular type of power

tool, taking into account the working conditions

and the work to be performed. Use of the power tool

for operations different from those intended could result

in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for impact drills

◆ Wear ear protectors with impact drills. Exposure to

noise can cause hearing loss.

◆ Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

Additional safety instructions for Australia and

New Zealand

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Side handle

6. Chuck

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting the side handle (fig. A)

◆ Turn the grip (7) counterclockwise until you can slide the

side handle (5) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit (fig. B)

◆ Open the chuck by turning the front part (8) with one hand

while holding the rear part (9) with the other.

◆ Insert the bit shaft (10) into the chuck and firmly tighten

the chuck.

Removing and refitting the chuck (fig. C)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw (11), located in the

front part of the chuck, by turning it clockwise using a

screwdriver.

◆ Tighten an Allen key (12) into the chuck and strike it with

a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Before drilling into walls, floors or ceilings, check

for the location of wiring and pipes.

Selecting the direction of rotation (fig. D)

◆ For drilling and for tightening screws, place the forward/

reverse switch (3) in the neutral position.

◆ For loosening screws or removing a jammed drill bit, turn

the forward/reverse switch (3) to the left.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

◆ For drilling in masonry, set the drilling mode selector (4) to

the position.

◆ For drilling in other materials and for screwdriving, set the

drilling mode selector (4) to the position.

Switching on and off (fig. E)

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

As a general rule, use low speeds for large diameter drill

bits and high speeds for smaller diameter drill bits.

◆ For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available

only at full speed.

◆ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CD70CKA in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker CD70CKA Manual

Product: