582917

Black Decker BL300 T1 Manual

4
Zoom out
Zoom in
Previous page
1/20
Next page
English (Original Instructions)
4
Before use, check the applian
c
e for damaged
or defective parts. Check for breakage of parts,
damage to switches and any other conditions
that may affect its operation.
Do not use the appliance if any part is
damaged or defective.
Do not use the appliance if the blade is
damaged.
Have any damaged or defective parts repaired
or replaced by an authorised repair agent.
Before use, check the power supply cord for
signs of damage, ageing and wear.
Do not use the appliance if the power supply
cord or mains plug is damaged or defective.
If the power supply cord or mains plug is
damaged or defective it must be repaired by an
authorised repair agent in order to avoid a
hazard. Do not cut the power supply cord and
do not attempt to repair it yourself.
Never attempt to remove or replace any parts
other than those specified in this manual.
Electrical safety
Before use, check that the mains voltage
corresponds to the voltage on the rating plate.
This appliance is double insulated in
accordance with EN 60335-2-14;
therefore no earth wire is required.
To avoid the risk of electric shoc
k, do not
immerse the cord, plug or motor unit in water or
other liquid.
Check that the supply voltage shown on the
rating plate of the appliance matches that of
your electrical system. Any connection error
will invalidate the guarantee.
Assembly
1. Wash all detachable parts (see chapter
‘Maintenance and cleaning’).
2. Fit the jug seal (E) into the blade holder (G).
3. Place the blade holder (G) into the jug base
(D).
4. Secure the blade holder (G) by turning it anti
clockwise.
Use
1. Place the appliance on a flat, stable surface.
2. Put the ingredients into the jug (C).
3. Push the lid (B) and filler cap (A) onto the jug
(C).
4. Place the jug (C) onto the blender body (I).
5. Secure the jug (C) by turning it anti
clockwise.
6. Connect it to the electrical supply and select
the required speed using the rotary switch.
The following settings are available:-
P = Pulse Operation
O = Power Off
1 = Low Speed
2 = High Speed
The appliance should be disconnected
from the mains supply before removing
the jug.
The Blender should not be run for longer than 60
seconds. After 5 consecutive runs of 60 seconds
use, the blender should be allowed to cool for at
least 60 minutes before further use.
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BL300 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BL300 T1 in the language / languages: English, Italian as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info